A structural component in the form of a wide plate is to be fabricated from a steel alloy that has a plane strain fracture toughness of 88 MPa √/m (ksi √/in.)) and a yield strength of 880 MPa (63820 psi). The flaw size resolution limit of the flaw detection apparatus is 3 mm (0.1181 in.). (a) If the design stress is one-half of the yield strength and the value of Y is 1.11, what is the critical flaw length? i mm (b) On the basis of this value, is a critical flaw subject to detection?

A structural component in the form of a wide plate is to be fabricated from a steel alloy that has a plane strain fracture toughness of 88 MPa √/m (ksi √/in.)) and a yield strength of 880 MPa (63820 psi). The flaw size resolution limit of the flaw detection apparatus is 3 mm (0.1181 in.). (a) If the design stress is one-half of the yield strength and the value of Y is 1.11, what is the critical flaw length? i mm (b) On the basis of this value, is a critical flaw subject to detection?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The creep data have been taken on an ahuminum alloy at 400°C and constant stress of 25MPA are shown in below Table, Find the steady state or minimum creep rate. Time (min) strain Time (min) 16 strain 0.135 0.0 0.0 2 0.025 18 0.153 4 0.043 0.065 20 0.172 0.193 0.218 22 0.078 24 10 0.092 26 0.255 12 0.109 28 0.307 14 0.120 30 0.368
4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows the steady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, how long the specimen would be? ( TH Trung Trong Stress (MPa) 1000 FTTinh Tru Trung Trung Trong th 800 600 400 200 100 80 60 40 815 C 20 d 10-6 104 10-5 650 C 730 C 925°C d d d d d 10-3 10-2 10-1 1 10 10² Steady-state creep rate (h-¹) 10³
For a given homogeneous, isotropic, linearly elastic material, E = 15e6 psi and v = 0.3. Solve for the shear modulus. 2.1.1 Homogeneous, isotropic, linearly elastic materials For specimens undergoing small deformations, the stress-strain diagram often ex- hibits a linear behavior. Although this is a very crude approximation to the behavior of actual materials, it is a convenient assumption that is often used for preliminary evaluation. A linear relationship between stress and strain can be expressed as 01 = E €1, (2.1) where the coefficient of proportionality, E, is called Young's modulus or modulus of elasticity. Since strains are non-dimensional quantities, this coefficient has the same units as stress quantities, i.e., Pa. This linear relationship is known as Hooke's law. The elongation of a bar in the direction of the applied stress is accompanied by a lateral contraction that is also proportional to the applied stress. The resulting defor- mations for this uniaxial state of stress…
a rectangular stepped bar is shown. the bar is loaded in bending. determine the fatigue stress concentration factor if the ultimate stress of the material is 690 mPa. please inlcude how to calculate the notch sensitivity.
P
Compute the elongation, in %, of a cylindrical copper rod if it is cold worked such that the diameter is reduced from 15.9 mm to 10.4 mm
A cylindrical steel bar 8 mm in diameter is loaded 1000 cycles per day with a load of 15560 N. How long until fatigue failure takes place? Note: stress = force/area Group of answer choices The bar should not fatigue. The bar will fail in one cycle. 100 days 1000 days
You have been given the following set of data from a soil-geotextile friction test: Normal stress (kPa) Peak shear strength (kPa) Residual shear strength (kPa) 17 20.2 13 35 31 22 70 52 39.5 140 94 74.5 (a) Plot the Mohr-Coulomb failure envelope (x-axis=normal stress; y-axis=shear stress) (b) Determine the peak friction angle, and the residual friction angle, . (c) Determine the peak adhesion and the residual adhesion. (d) Calculate the fabric efficiency based on a soil friction angle of = 35-degrees using the peak friction angle. **HINT: the equation for efficiency of soil friction angle mobilization is: