2. The Goodman diagram relates oa and Om for fatigue failure after a specific number of cycles N₁, where da is the cyclic stress amplitude, and on the mean stress. For a steel specimen it is found that oa = a (0).[1- (om/OTS)] where OTS is the metal's tensile stress (375MPa), and oa (0)~0.450TS is the 107 cycle fatigue limit at zero mean stress. Assuming the specimen is cycled repeatedly between 0 stress and a peak stress, what is the maximum peak stress if failure in < 107 cycles is to be avoided?

2. The Goodman diagram relates oa and Om for fatigue failure after a specific number of cycles N₁, where da is the cyclic stress amplitude, and on the mean stress. For a steel specimen it is found that oa = a (0).[1- (om/OTS)] where OTS is the metal's tensile stress (375MPa), and oa (0)~0.450TS is the 107 cycle fatigue limit at zero mean stress. Assuming the specimen is cycled repeatedly between 0 stress and a peak stress, what is the maximum peak stress if failure in < 107 cycles is to be avoided?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the S-N Curve below to answer the following questions 550 mT 500 450 400 350 300 250 200 150 100 50 10 Fatigue life (cycles) 10? 103 105 106 107 Stress amplitude (MPa)
Which of these cracks will lead to failure first from the table in the picture? And present your findings in a table format and comment briefly.
In mechanical resistance
Q1/ The table below shows the values of stress amplitude and life cycles : Fatigue strength Sf (Mpa) Number of cycles (Nf) 474 111 417 496 352 3002 316 7065 290 21930 262 66075 The test were done, to estimate the failure, on un-notched axially load specimens under zero mean stress. Calculate a and b using the stress -life equation.
Equiaxed MAR-M 247 alloy is to support a stress of 276 MPa (Fig. 7.31). Determine the time to stress rupture at 850°C. Larsen-Miller parameter, P = [TCC) + 273] [20+ log()] × 10-³ 23.3 24.4 25.5 26.7 27.8 28.9 22.2 30 31.1 DS MAR-M 247 longitudinal MFB, 1221°C/2 t/GFO, 982°C/5 h/AC. 871°C/20 h/AC, 1.8 mm diameter production data Equiaxed MAR-M 247 MFB. 982°C/5 W/AC+871°C/20 W/AC and 871 C/20 h/AC only. 1.8 mm diameter specimens Stress (MPa) 690 552 414 276 207 DS CM 247 LC, longitudinal. 1232°C/2h+1260°C/20 W/AC 982°C/5 h/AC, 871°C/20 V/AC 3.2 and 4.1 mm diameter specimens 138 100 80 60 40 30 20 10 DS CM 247 LC longitudinal," 1232°C/2h+ 1260°C/2 MAC.T 1079 C/4 WAC, 871°C/20 W/AC and 1232°C/2h+1260°C/20/AC. 1050°C/16h/AC, 871°C/20 WAC 3.2 and 4.1 mm diameter specimens 40 48 50 52 54 56 42 44 46 Larsen-Miller parameter, P = [T(F) + 460] [20+ log()] x 10-3 Figure 7.31 Stress (ksi)
A circular steel bar with a length of 200 mm and a radius of 2 cm is strained in a tensile test to point B on the stress-strain curve shown below, and is then unloaded. What is the permanent change in the length of the bar compared to its original length? Stress (MPa) 350 300 250 200 150 100 50 0 0 elastic limit 1.0 2.0 Point B 3.0 Strain (%) 4.0 5.0
The shear modulus, G, of an alloy can be determined by measuring the angular twist, θ,resulting from a torque applied to a cylindrical rod made from the alloy. For a rod of radius Rand a torque applied at a length L from a fixed end, the modulus is found by G=2LT/pR4θ.Examine the effect of the relative uncertainty of each measured variable on the shearmodulus. If during test planning all of the uncertainties are estimated to be 1%, what is theuncertainty in G?
Asiacell 4,ll ON 76% D19:17 سؤال الواجب.docx Problem :- The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30 mm: load(KN) 0 40 80 95 90 135 150.2 145 130 120 elongation(mm) 0 0.022 0.13 0.25 0.55 2.01 3.88 4.12 5.22 6 Plot engineering and True (stress-strain) curves, then determine the (oy, ɛy), (ou, ɛu), (of, , ef), ductility , modulus of elasticity . Then select on the drawing (strain hardening (n)), (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region)?
The following creep curve is derived from an aluminum alloy tested at 380℃ with a constant stress of 2.50 MPa. Identify in the illustration the 3 stages of creep. Determine the steady-state creep rate and the rupture lifetime.
Correct and complete solution please
Calculate the (total tensile strength) of the mitotic tensile strength test for the information in the table below: Time # D mm Load Kn sec 1 60 16 14 2 54 15.5 14 3 57 16 15.5 4 52 15 18 5 53 15 14 59 17.5 19 50 9 17 56 19 21 58 10 21.4 55 11 25 67899 10
Q (2): A laboratory experiment has been executed to calculate the thermal conductivity of a specimen. The specimen is a bar with (Diameter= 0.04 m) and (length = 0.06 m). At steady state condition, the following data have been recorded: Voltage(V) Current(A) 8 0.8 T₁ (°C) 46.8 T₂ (°C) T3 (°C) 42.2 34.6 T. (°C) 31.4 By taking into consideration that the temperature changes linearly with position, refer to the figure aside, and calculate he thermal conductivity for the specimen (intermediate section). T₂ T₂ The face Told face T₂ T₂ 6 cm 4 cm 6 cm 4 cm 6 cm Hot section Int. section Cold section