Source IP 1.2.3.4 1.2.3.4 1.2.3.4 1.2.3.4 5.6.7.8 Destination IP 5.6.7.8 5.6.7.8 5.6.7.8 5.6.7.8 1.2.3.4 Source Port 23456 23456 23456 23456 443 Provide responses for the following given the table above. 1. What is the IP address of the client Destination Port 443 443 443 443 23456 Number of Bytes 105678 904567 94856 497989 2500

Source IP 1.2.3.4 1.2.3.4 1.2.3.4 1.2.3.4 5.6.7.8 Destination IP 5.6.7.8 5.6.7.8 5.6.7.8 5.6.7.8 1.2.3.4 Source Port 23456 23456 23456 23456 443 Provide responses for the following given the table above. 1. What is the IP address of the client Destination Port 443 443 443 443 23456 Number of Bytes 105678 904567 94856 497989 2500

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

COURSE: COMPUTER NETWORKS
B. Assume the following forwarding table for a router: Destination network Exit interface 172.58.128.0 /17 172.58.128.0 /19 1 172.58.160.0 /19 2 Otherwise Which exit interface the router will use if the arrive packet with the following address: Destination address 172.58.218.80 172.58.165.90 Exit interface 2. 172.58.124.36 172.58.155.122
Q5) 1- Write the routing table for router R1 for the networks N2, N3, and Host B. 2- Define: RIP protocol, Timers, Drawbacks and explain the algorithm used by RIP protocol. 3- Consider the following network, using RIP protocol: N1 N2 N3 N4 201.4.16.0/22 201.4.22.3/24 R2 180.70.65.128/25 180.70.65.192/26 RI R3
10.0.0.0/8 Fa0/1 Fa0/2 Fa0 S2 Gigo/0 Se0/00 Server 192.168.1.024 R2 O Seo/00 Seo/01 192.168.20/24 Gigo/o 172.16.0.0/16 Gigoio 192.168.4.0/24 Fa0/1 Fa0/1 Fa0 Fa0/2 Fa0/2 Fa0 PC2 $1 S3 PC1
PC-PT PC-PT POPT PE2 PC5 PCPT PC4 2960 24TT Sw1 192.168.10.1 192.168.30.1 10.10.10.2 2811 10.10.20.2 2950T-24 SW2 Switth-PT SW3 2811 R2 R3 192.168.20.1 10.10.20.1 PC-PT 10.10.10.1 PC-PT PC3 PCO 2811 R1 Q. 2 (a) When dynamic routing would be preferred over static routing? Refer to the above figure, a summarized static route has been configured in Router R1. R1(config)# ip route 192.168.0.0 255.255.0.0 10.10.20.2 Will this command create any problem? Yes or No. Explain.
[15] IP ADDRESS DECODING: IP: 139.182.148.50 NM: 255.255.254.0 128 64 32 1 1 1 NA: NETWORK ADDRESS 16 8 1 1 OR BA: BROADCAST ADDRESS AND 255.255.254.0 = 11111111.11111111.11111110.00000000 10001010.10110110.10010100.00000000 139. 182. 148. 0 NA: 4 1 BA: 2 1 1 1 139.182.148.50=10001010.10110110.10010100.00110010 139.182.148.50 = 10001010.10110110.10010100.00110010 255.255.254.000000000.00000000.00000001.11111111 PRACTICE: PLEASE CALCULATE [NA: Network Address] AND [BA: Broadcast Address] IP: 172.16.0.100 ● NM: 255.255.252.0 10001010.10110110.10010101.11111111 139. 182. 149 . 255 (First Address of the Network) (Last Address of the Network)
Find & define the IP addressing problem. 192.168.1.33 Default gateway 192.168.162 1900 FO/27 FO/26 192.168.1.66 Default gateway: 192.168.1.95 FOO 192.168.1.62/27 SO/O FO/2 50/0 2950 192.168.1.65 Default gateway 192.168.1.95 192.168.1.97/27 192.168.1.100/27 F0/3 FO/1 FOO 192.168.1.95/27
Subject- Data communication Networks 1) A router has just received the following new IP addresses: 128.14.120.0/23, 128.14.118.0/23,128.14.114.0/23, and 128.14.110.0/23. If all of them use the same outgoing line, can they beaggregated?
Configure OSPF process for single area-0 (backbone) on R2
PC4 192.168.B. 120/24 PC3 192.168.B.125/24 PC1 192.168.A.5/24 PC2 192.168 A 10/24 Switch 1 Questions : D1 192.168.A. 1/24 Switch 2 R1 Network Address Destination E1 192.168.B.1/24 E2 10.200.B.5/28 D2 10.200.B.10/28 Value of A = 29, B = 32, C = 33, D = 34 D3 10.10.B.193/28 E3 10.21.B.5/30 F2 10.21.B.6/30 Next hop F3 10.10.B.200/28 R3 1. Determine the Routing Table for R1, R2, and R3 using the following table F1 192.168.C.1/24 Switch Interface PC6 192.168.C.16/24 PC5 192.168.C.18/24 2. With the Routing Table that you have specified in point d, which path will PC2 take when communicating with PC3 and PC5 and vice versa?
For the interface with a configuration of 192.168.4.82 255.255.255.224 the network size is: O 224 5. O32 O 64 O 256 6. For the interface with a configuration of 192.168.4.82 255.255.255.224 the network base address is: O 192.168.4.80 O 192.168.4.32 192.168.4.64 O 192.168.4.224