(20 points] See table below.Destination IPSource IP1.2.3.44.3.2.12.1.3.43.1.2.35.4.8.2Source Port100.101.102.103 23456100.101.102.104 33333100.101.102.103 44444100.101.102.104 44567100.101.102.108 21342Destination Port Number of Bytes105457890445673294855495798925908005380538053Describe the function of each IP address listed above and the type of activity that isoccurring based on the evidence in the table above.

Communication endpoints are represented by ports like 80,53 and so on which determine the network…

(20 points! See table below. Destination IP Source 1 1.2.3.4 4.3.2.1 2.1.3.4 3.1.2.3 5.4.3.2 Source Port 100.101.107.103 23456 100.101.102.104 33383 100.101.102.103 44444 100.101.102.104 44567 100.101.102.108 21342 Destination Port Number of Bytes 1054678 9044567 3294855 4957989 2590800 53 80 53 80 53 Describe the function of each IP address listed above and the type of activity that is occurring based on the evidence in the table above.

(20 points! See table below. Destination IP Source 1 1.2.3.4 4.3.2.1 2.1.3.4 3.1.2.3 5.4.3.2 Source Port 100.101.107.103 23456 100.101.102.104 33383 100.101.102.103 44444 100.101.102.104 44567 100.101.102.108 21342 Destination Port Number of Bytes 1054678 9044567 3294855 4957989 2590800 53 80 53 80 53 Describe the function of each IP address listed above and the type of activity that is occurring based on the evidence in the table above.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write the Network Address, Broadcast Address and UIP of the following address. 200.100.4.5/26 192.168.3.32/ 15
Consider the Ethernet networks shown in the below exhibit to answer the following questions. Fa0 Fal PC3 PCO Fa0/1 Fa0/0 Fa0/3 Etho/D/0 Fa0/2 s1 Fa0/1 R1 Fa0 Fa0/0 Fa0/1 PC1 R2 Fa0/1 Fa0/3 S2 Fa0 PC2 The network interface settings of POs are: Logical Address Physical Address PCO 192.168.2.2 0060.5032.9A15 PC1 192.168.2.3 o001.6363.6BAA PC2 192.168.3.2 O0EO.F9A1.0864 PC3 192.168.0.2 0001.0935.08C3 The network interface settings of routers are: Logical Address Physical Address R1-Fa0/0 192.168.0.1 0004.9A31.0501 R1-Fa0/1 192.168.1.1 0004.9A31.0502 R1-Etho/0/0 192.168.2.1 0060.2F70.0D9B R2-Fa0/0 192.168.1.2 0002.1641.6301 R2-Fa0/1 192.168.3.1 0002.1641.6302 Suppose that the switching table in the S1 contains the following contents: Fa0/1 Fa0/2 Fa0/3 Fa0/4 Open Fa0/5 Fa0/6 Fa0/7 Fa0/8 Open Open Open Open If a frame with source MAC address 001.6363.6BAA and destination MAC address 0060.5032.9A15 is received at the switch, at which port does the frame arrive? Which port(s) will the frame go…
PC4 192.168.B. 120/24 PC3 192.168.B.125/24 PC1 192.168.A.5/24 PC2 192.168 A 10/24 Switch 1 Questions : D1 192.168.A. 1/24 Switch 2 R1 Network Address Destination E1 192.168.B.1/24 E2 10.200.B.5/28 D2 10.200.B.10/28 Value of A = 29, B = 32, C = 33, D = 34 D3 10.10.B.193/28 E3 10.21.B.5/30 F2 10.21.B.6/30 Next hop F3 10.10.B.200/28 R3 1. Determine the Routing Table for R1, R2, and R3 using the following table F1 192.168.C.1/24 Switch Interface PC6 192.168.C.16/24 PC5 192.168.C.18/24 2. With the Routing Table that you have specified in point d, which path will PC2 take when communicating with PC3 and PC5 and vice versa?
R2(config)# router ospf 20 R2(config-router) # router-id 2.2.2.2 R2(config-router) # network 192.168.10.0 0.0.0.3 area 0 R2(config-router) # network 10.2.1.0 0.0.0.255 area 0 R2(config-router) # end R1(config)# router ospf 10 R1(config-router) # router-id 1.1.1.1 R1(config-router) # network 10.1.1.0 0.0.0.255 area 1 R1(config-router) # network 10.1.2.0 0.0.0.255 area 1 R1(config-router) # network 192.168.10.0 0.0.0.3 area 1 R1(config-router) # end Refer to the exhibit. Why are routers R1 and R2 not able to establish an OSPF adjacency? 1. Open Packet tracer and replicate the topology. 2. Refer on the configuration and load them in your topology 3. Apply the correct configuration 4. Test PC with 10.1.1.10/24 should be able to ping 10.2.1.10/24 5. Record your testing and save it as MP4 format. Area 0 10.2.1.0/24 GO/0.1 192.168.10.0/30 Area 1 .2 S0/0/0 .1 R2 10.1.1.0/24 SO/0/0 R1 GO/O G0/1 .1 10.1.2.0/24