Packet Tracer File (Design your own network) Requirements: 1 Routers Configured with basic configuration 1 Switches Configured with Vlan10, within this switch 5 PC is connected (172.168.20.0/28) 1 Switches Configured with Vlan200, within this switch 2 PC is connected (192.168.50.0/29) PC from VLAN 10 should be able to Connect to PC in VLAN 200 and vice versa Both Router and Switch should have these properties. Name R1[Your Initial], S1[Your Initial], S2[Your Initial] Banner [Put your name] Passwords use this as a password to all CPENET2EXAM You can decide for other Ip addresses and VLAN Needed All configurations should be documented

Q: 1. Calculate the bandwidth-delay product for the following networks: (1) T1 (1.5 Mbps). (2) Ethernet…

A: 1. Calculate the bandwidth delay: 1) TI (1.5Mbps) bandwidth value = 1.5Mbps x 1000 kilobits x 1000…

Q: Choose a CORRECT statement on the Ethernet technology. Switches do not regenerate arrived signals in…

A: For network communication, Ethernet employs a technique known as CSMA/CD (Carrier Sense Multiple…

Q: Explain the various memory found in a CISCO router.

A: Intro When it comes to today's most demanding network services — such as IP communications, video,…

Q: What is the purpose of a router in a network, and which OSI layer does it primarily operate at?

A: Purpose of a Router in a NetworkA router serves as a device that forwards data packets between…

Q: Routero Fa0/0 10.10.10.1/24 no switchport Fa0/3 10.10. 10.2/24 trunk Fa0/1 trunk trunk Fa0/1 Fa0/2…

A: The answer given as below:

Q: Design your own network Requirements: 1 Routers Configured with basic configuration 1 Switches…

A: A virtual LAN (VLAN) which refers to the logical overlay network that groups together a subset of…

Q: STP and Etherchannel Consider the below topology, noting that all the switches have the same…

A: Q1(a) ​​​​​​ From the given topology, Primary Root Bridge = SWC Secondary Root Bridge = SWD…

Q: You are asked to design a MAC protocol for an access network where N nodes generate data…

A: MAC protocol : MAC protocol is the first protocol layer above the Physical Layer in ad hoc.…

Q: Switch Configuration Sw-1 e0/0 e1/0 eo/1 eo 2 e0/3 Mgmt-PC VPCS VPCS VPCS VPCS PC1 PC2 PC3 PC4…

A: Given:

Q: a- Given the following screenshot, some errors are preventing PC-C from accessing the Redundant…

A: Introduction: In part a we are provided with few lines of code and we have to remove errors from it.…

Q: INSTRUCTION: 1. Construct the Network Diagram below using Fast ethernet or LAN cable. 2. Using the…

A: Computer networking which refers to interconnected computing devices that they can exchange data and…

Q: You have been asked to bond/aggregate 4 of the gigabit ethernet connections between two switches to…

A: B) LACP

Q: LAN CREATION AND CONFIGURATION BOTH     DO ASAP

A: VLAN CREATION:-.Switch(config)#hostname S1 S1(config)#vlan 10S1(config-vlan)#name…

Q: The kind of cable used to link the switch and the router must be determined. What piece of hardware…

A: Dear Student, The piece of hardware that is used to connect two networks operating under distinct…

Q: Default gateway for PC1 and Laptop. i) Total number of local area networks shown in Figure 4-1. ii)…

A: Here a network topology is given in Fig 4.1 and it needed to be analyse for determining some…

Q: 4-1. Illustrate the following to him. 192.168.1.65 0003 E4CC 2E02 Gigo1 192.168.1.1 0003 E4CC 2E01…

A: 1) Default gateway of PC1 is 192.168.1.1 and laptop is 192.168.1.65 Default gateway is the node…

Q: In the OSI model, what distinguishes a Layer 2 switch from a Layer 3 switch, and how do their…

A: In this question we have to understand - In the OSI model, what distinguishes a Layer 2 switch from…

Q: Figure 1(e) shows a network of two VLANs that are connected to a router. Both VLANS use the last…

A: Create and name the VLANs. First, the VLANs are created and named, as shown in Example 4-1. VLANs…

Q: Two access layer switches sw1 and sw2 are connected by four fast ethernet links. (i) Describe any…

A: STP - Spanning Tree Protocol is used to remove the loops which are created by redundant links…

Q: In TCP/IP Network Access Layer Protocols: If you are in KICT building and connect your wireless…

A: the answer is given below:-

Q: Configure the following VLans having two switches: Switch 1: 1. VLan 40, Dept. HR 2. VLan 50, Dept.…

A: V LAN is a virtual LAN in this physically system can be placed anywhere but they are logically…

Q: 5- The four pairs share a common middle hop with a transmission capacity of R = 400 Mbps. The four…

A: Here is the explanation of the above problem. See below steps.

Q: 2) Logical Addressing: - Incorporate the following IPV4 private addressing scheme on the LANS - LAN…

A: ANSWER:-

Q: 5-The four pairs share a common middle hop with a transmission capacity of R = 400 Mbps. The four…

A: Given that, Middle hop transmission capacity (R)= 400 Mbps Transmission capacity of four servers…

Q: Computer Science assume a frame is traveling from Station A to Station B. The switches have been…

A: Actually, LAN is a Local Area Network.

Q: When a switch receives a packet, how does it know if the packet should be delivered to any of the…

A: When a switch receives a packet.  it know if the packet should be delivered to any of the connected…

Q: Set up the following: There are two switches on VLans: Switch 1) VLan 10, Dept. Admin (Ports:…

A: CISCO PACKET TRACER is used to solve the given problem.

Q: 1. Calculate the bandwidth-delay product for the following networks: (1) T1 (1.5 Mbps). (2) Ethernet…

A: 1. Calculate the bandwidth-delay product for the following networks: (1) T1 (1.5 Mbps). (2) Ethernet…

Q: 1. Calculate the bandwidth-delay product for the following networks: (1) T1 (1.5 Mbps). (2) Ethernet…

A:

Q: Describe five factors that ACLs employ to allow or prevent traffic on a router.

A: Answer 1. Standard and extended access lists can't share the same names. 2. We are unable to remove…

Q: 14. Which of the following could not be an Ethernet multicast destination? a. B7:7B:6C:DE:10:00 b.…

A: Here is the solution which is mentioned below:

Q: PC to PC connection is requirec Cable is unknown Switch to switch connection rec Router to Router…

A: Dear Student, The Auto MDIX feature is best to use when a PC to PC connection is required. This is…

Q: MAC address on hosts, switches and routers? Explain Draw the switch table (fully populate

A: Do we need to configure MAC address on hosts, switches and routers? Explain Draw the switch table…

Q: When implementing a network with WAN technologies, which of the following must be known? (select…

A: Introduction: Understanding the devices and technology involved is crucial when constructing a Wide…

Q: Explain in detail about vty in cisco router.

A: VTY : Vty is a virtual port and its stands for Virtual Teletype. It is for providing inbound…

Q: a) Answer the following questions based on the routing table shown in Figure 3-1. RouterJ# show ip…

A: L— "Identifies the address assigned to a router’s interface" C— "it Identifies a directly connected…

Q: addresses and Priority IDs. Implement the STP standard IEEE 802.1D. Show the following on the…

A: Here we  find separately. Root Bridge: Steps to find route bridge 1.In every spanning tree protocol…

Q: Set up the following: There are two switches on VLans: Switch 1) VLan 10, Dept. Admin (Ports:…

A: We will use Cisco Packet Tracer to solve the given networking problem.

Q: Describe the responsibilities of a Layer 3 switch in the OSI model. How does it combine features of…

A: Layered architecture, also known as layered software architecture, is a fundamental design pattern…

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.