500-24 24 Instruction: 1. Configure OSPF routing protocol on the network given above 2. Subnet the network 192.168.5.0/24 1. Network 1 requires 120 host 2. Network 2 requires 60 host 3. Network 3 requires 30 host 4. Network 4 requires 2 host point to point between router to router 5. Network 5 requires 2 host point to point between router to router 6. Network 6 requires 2 host point to point between router to 3. Complete the table 1 given in the next page. 192.168.5.130

Q: Refer to this exhibit they are connected to each router with OSPF routing protocol, and they both…

A: The fundamental benefit of a link state routing protocol like OSPF is that routers can generate…

Q: Question 22 IEEE S02.1q is used Only on Cisco equipment Along with IEEE 802.3ac Only with ISL With…

A: Since you have asked multiple questions as per guidelines we can answer only one please repost the…

Q: (c) Assume a router has the following entries in its routing table (cf. Table 1). Table 1: Router…

A: Given:   Assume a router has the following entries in its routing table (cf. Table 1).   What route…

Q: we obtain the following information from one router. What kind of routing protocol does it use?…

A: Here use ony Routing information protocol. we can use it wiht local area network for small ranges.…

Q: Based on Figure, write a series of ACL statements that allow only traffic from source host…

A: The Access control is a security technique that can be used to regulate who or what can view or use…

Q: 4. Mention the TCP/IP layer(s) related to each device in the network. 5. If (PC A) sends a frame to…

A: A network is, broadly speaking, an assembly of linked devices, systems, or entities that are…

Q: w how it finds the network and the subnetwork address to route the packet. A otwork required in four

A: The answer is

Q: Consider a router that interconnects subnets A and B, as shown in the figure below. Suppose all of…

A: In the context of network infrastructure, routers play a crucial role in interconnecting different…

Q: Where is a packet to each of the tollowing destinations forwarded? a. 128.96.39.10 b. 128.96.40.12…

A: ANS:  it is very simple to check  the packet is forwarded to which interface by simply bitwise "AND"…

Q: switch 3 192.168.3.0/24 1 2 3 4 5 6 000000 192.168.3.8 255.255.255.0 192.168.3.1 AAA3 Router 2…

A: The objective of the question is to determine which router interface will first receive an IP packet…

Q: Router A sends two RIP messages to two intermediate neighbouring routers, B and C. Do the two…

A: Step 1: Routing Information Protocol (RIP) Messages Source and Destination IPs for RIP…

Q: 1. A router receives a packet with destination address (please refer to the table attached to find…

A: The following is the solution

Q: Which statements about routing protocols are true. choose 2 A) OSPF is a distance vector protocol.…

A: The correct statements about routing protocols are:   B) True. RIPv1 is a classful routing protocol…

Q: If R1 with the following table received a packet with the destination address 11.2.3.4 the router…

A: ExplanationThe first mask(/26) is applied to the destination address.The result is 180.70.65.128…

Q: QUESTION 21 SDN (software driven network) router can act as a traditional router True False   5…

A: Answer is given below .

Q: Based on lab exercise in P2 (Figure 2), answer the following questions: a. How many targets are…

A: Dear Student, nmap 161.139.246.215-219 Will scan for 5 target hosts ie 161.139.246.215,…

Q: Using the following topology, write the three routers R1, R2 and R3 routing table based on dynamic…

A: By using the following topology ,the three routers R1,R2 and R3 routing table based on dynamic…

Q: Which two statements about routing protocols are true? (choose 2) A) OSPF elects designated routers…

A: Option A) is incorrect as     OSPF elects one router to serve as the designated router (DR) and…

Q: A router uses the following routing table- A packet bearing a destination address 144.16.68.117…

A: The following Routing table is given. according to the question, A packet bearing an estimation…

Q: Based on the number of commands lines, discuss whether static routing or dynamic routing is the more…

A: Topology control: BGP, EIGRP, OSPF, and RIP are examples of routing algorithms that you can use…

Q: a) A packet enters a router. Assume the router spends 0.01ms processing the packet. The router…

A: According to the question, we have to explain the four sources of delay in the network according to…

Q: The correct physical address in mark 1 in the following network is A/10 To another | X/44 network…

A:

Q: 1. Consider the following switched Ethernet network with redundant core switches. E S5 B- S1 S3 D-…

A: Spanning Tree Protocol(STP) It is a network protocol which builds a loop-free logical topology for…

Q: 6- Which of the following is the multiple access protocol for channel access control? a) CSMA/CD b)…

A: NOTE  :-  As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly…

Q: True or False 1. In 802.11 CSMA/CA, when a station senses the medium to be idle it sends a frame…

A: All the above question is based on TCP transfer control protocol which is a protocol in networking…

Q: Consider the network depicted in the below figure. Suppose that router R1 receives a packet Pktl…

A:

Q: LSM Review Exercise ou are tasked with designing the VLSM IP Addressing Major Network…

A: To design a VLSM ip addressing. It comes under Computer networks. VLSM ->Variable Length Subnet…

Q: 1. It is known that the MAC address is the only address that is used in order to communicate and…

A: Given- eg1

Q: There is a routing table in the figure on a router.  If packets with the following destination IP…

A: The routing table given is:- Address  Next hop 198.52.60.0/23 Ethernet 0 198.52.62.0/23…