Pls show neat and whole solution Solve the following problems as directed.1.An inductive load consumes 20 kW at 75% lagging power factor. A synchronous motor with a90% power factor is connected in parallel with the inductive load. What minimum kW size of thesynchronous motor is needed so that the overall power factor is 85% lagging.

Answered: Solve the following problems as…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter39: Synchronous Motor Operation

Section: Chapter Questions

Problem 14SQ: Induction motors and welding transformers require magnetizing current, which causes a. lagging power...

See similar textbooks

Similar questions

A generator is feeding the load. A second load will then be connected in parallel with the first load. The generator has an idle frequency of 61Hz and an Sp slope of 1MW/Hz. Load2 draws 800kW active power at 0.707 reverse power factor, while load1 draws 1000kW active power at 0.8 reverse power factor. What will be the operating frequency of the system after load 2 is connected? *Please explain the solution step by step
A 60 Hz generator is connected to a turbine operating under a head of 3000 ft with a flow of 80 cubic ft / sec. The turbine specific speed is 3 rpm and a turbine efficiency of 80%. a.) Determine the number of poles of the generator
explain the phasor diagram of slip phase induction motor
• - 1800 pm In a two pole 3-p synchronous generator, the peak flux of rotor magnetic field is o5Tand the rotor rate of rotation is 1800 rpm. The stator windings have a surface area of 0.1 m? and there are 50 turns per Bmax : 0.5T, 0.5T coil. The machine is A-connected. A: 0-1 m? N: 50 a) What is the RMS phase and line voltage of the generator? b) Write the three stator phase voltages as functions of time.
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
Explain how the real and reactive power is controlled in synchronous generators.
Please answer all subparts for like either dislike is ready Answer in short please. All subparts..
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
4. An induction motor draws 4.5 A at a 0.75 lagging power factor from a 208V, 60 Hz source. a) What value of capacitance must be connected in parallel with the motor to raise the overall p.f. to 1. b) Calculate the magnitudes of the motor current, capacitor current and source current with the capacitor in place. 5. A 3-phase Y-connected motor is connected to a three phase Y-conected source with 440V line voltage. It draws a line current of 5A from the source. If the power factor of the motor is 0.8, calculate a) Active power and Reactive power absorbed by the load b) Total Apparent power
At a location in Europe, it is necessary to supply 300 kW of 60-Hz power. The only power sources available operate at 50 Hz. It is decided to generate the power by means of a motor-generator set consisting of a synchronous motor driving a synchronous generator. How many poles should each of the two machines have in order to convert 50-Hz power to 60-Hz power?
In a workshop, there is a three-phase asynchronous motor with a power of 6 HP, an efficiency of 85%, and a power factor of 0.8. Find the capacitor capacity required for power factor correction in the workshop. (The capacitors will be connected in a delta configuration.) A new power factor of 0.95 is desired. The nominal voltage in the workshop is given as 0.4 kV. (1 HP = 0.745 kW)

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS