Solve and please show an eligible solution: 1. Refer to Figure 1. A Y-connected source supplies 3 balanced 3-phase loads. The source has voltage Vab=38020 V. a. Assume that load 1 is A-connected, what are the phase voltages & currents in that load? b. Assume that load 2 is Y-connected what are the phase voltages & currents in that load? c. What real, reactive and apparent power does the generator supply when the switch is open? Y-Connected 100kW Source 0.9 LAG 80KVA d. What are the line currents (la, IbB, lec)? e. What real, reactive and apparent power does the generator supply when the switch is 0.8 LAG Figure 1 80kW closed? 0.85 LAG f. What are the line currents when the switch is closed? g. Determine the value of each capacitor when a Y-connected capacitor bank is to be connected in parallel with the loads to raise the PF to 0.95.

Solve and please show an eligible solution: 1. Refer to Figure 1. A Y-connected source supplies 3 balanced 3-phase loads. The source has voltage Vab=38020 V. a. Assume that load 1 is A-connected, what are the phase voltages & currents in that load? b. Assume that load 2 is Y-connected what are the phase voltages & currents in that load? c. What real, reactive and apparent power does the generator supply when the switch is open? Y-Connected 100kW Source 0.9 LAG 80KVA d. What are the line currents (la, IbB, lec)? e. What real, reactive and apparent power does the generator supply when the switch is 0.8 LAG Figure 1 80kW closed? 0.85 LAG f. What are the line currents when the switch is closed? g. Determine the value of each capacitor when a Y-connected capacitor bank is to be connected in parallel with the loads to raise the PF to 0.95.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

三 T AaBbCcDc AaBbCcDc AABBC T Normal 1 No Spac. Heading Paragraph Styles In the circuit pictured the current through R1 is 11 = 6A in the direction shown. a) Determine the current 14. Describe choice of node or loop (including direction of travel). b) Determine the current 13. Describe choice of node or loop (including direction of travel). c) Determine the Determine the potential difference Vgd = Vg Vd between points g and d.
current - 1=?, and the power factor - cosp =?. 4. An out of balance three phase star connected load has the following complex currents: I₁ = lejº,A, I₂ =le¯6⁰,A and I₁=1e¹j6⁰, A. This load is supplied by a four wire power line from a balance voltage source. Find the r.m.s. value of the neutral current Io =? Wait to th
Please answer correct with reason
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
An AC voltage source delivers current to Load A and Load B which are connected in parallel. Current in Load A is 25 A and Current in Load B is 42.2. If the current in load B leads the current in load A by 45 degrees, calculate: a) Resultant or total current, b) Angle between the resultant current and Load current A if Load Current A is at reference or zero degrees.
SHOW COMPLETE SOLUTION A. What is the overall power factor of the two loads as seen by the source? Use two decimal places. B. Determine the magnitude of the current passing through Load 1. Use amperes and two decimal places. C. Is the overall power factor leading or lagging?
Problem 1- Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: A. B Zs (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (13) through impedance Z4. 220V;50HZ Figure 1 Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar Take voltage as reference. notation.
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Mesh analysis
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Nodal analysis.
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.
Question 1 Refer to the circuit depicted in Figure Q4 (b). Solve the circuit by finding the value of current that going through each branch in the circuit. I2 0.25 F 10 cos(2t + 30) v 1H Figure Q4 (b) Question 2 At o= 50 rad/s, determine Zin for the circuit in Figure Q4 (a). 10 mH 10 mF Zin Figure Q4 (a)
Discuss Fully the various methods available for transforming 3-phase voltages to higher or lower 3-phase voltages. Highlight the advantages and disadvantages of each. Include the connection diagrams.