Sketch volt) for the half-wave rectifier shown in Figure 1. 2.2KΩ vi(t)=10 sin 120xtV Vit volt) Figure 1 Half-Wave Rectifier 2. Sketch vo(t) for the bridge rectifier shown in Figure 2. vet) 4 vi (t) = 10 sin 1207tV 2.2K2 Figure 2 Bridge Rectifier 3. a. b. What is the frequency of the specified input voltage in Parts 1 and 2 above?

Sketch volt) for the half-wave rectifier shown in Figure 1. 2.2KΩ vi(t)=10 sin 120xtV Vit volt) Figure 1 Half-Wave Rectifier 2. Sketch vo(t) for the bridge rectifier shown in Figure 2. vet) 4 vi (t) = 10 sin 1207tV 2.2K2 Figure 2 Bridge Rectifier 3. a. b. What is the frequency of the specified input voltage in Parts 1 and 2 above?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
How is a solid-state diode tested? Explain.
Q3: The figure below includes a bridge full-wave rectifier circuit with a diode type is1N4007. The input voltage is Vin V2 120 sin 2n60t 5:1 D3 D1 120 V RL Vp(out) D2 DA 10 kN a) Draw the output voltage waveform for the circuit in the figure and include thevoltage values. b) What is the peak inverse voltage (PIV) across each diode? c) Determine the rms voltage, current and power delivered to RL d) Determine the average voltage, current, and power delivered to RL e) What is the ratio of Po(de) to Po(ac)? lll
A full wave bridge rectifier is supplied from 230V, 50Hz and uses a transformer of turns ration 15:1. It uses load resistance of 50 ohms. Calculate load voltage and ripple voltage. Assume ideal diode and transformer. Assume ripple factor equals to 0.482. a.Load Voltage= 13.8 V; Ripple Voltage=6.652 V b.Load Voltage= 15.6 V; Ripple Voltage=7.611 V c.Load Voltage= 21.3 V; Ripple Voltage=8.410 V d.Load Voltage= 25.1 V; Ripple Voltage=10.442 V
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
1. A heavily inductive load of R-502 is to be supplied with a DC voltage of 200 V. using three-phase bridge rectifier. Calculate: (a) The DC load current. (b) The RMS current of any diode. (c) The transformer secondary phase current. (d) The transformer secondary line voltage. (e) PRV of any diode. 2 Reneat Olahove if the rectifier is three-nhase half-wave tyne.
This one.
Find Vpc if VAN = VBn = Vcn= 120 volts... Half-wave Three-phase Rectifier Conduction Waveform Periodic Time (T) A B A 90° 180° 360 450° 540 time 270° -V VAN VeN VaN VaN VEN Voc4 Voc 150 120° 270 390 510° time 30 Output Voltage Waveform
Part A, B and C
8 5. In a single-phase diode bridge rectifier circuit fed by a source voltage of 240 50%THD and a fundamental of 10A(rms). The power drawn is 2kW, Calcu a) The DPF b) The distortion current Idistortion c) The total current Is J The PF