Situation 5. A rectangular beam with limited size of 300 mm wide is to be designed for an ultimate moment of 550 kN m with f'c = 28 MPa and fy = 420 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. 13. Determine the maximum tensile steel ratio if the tensile steel strain will not be less than 0.005 for a more ductile failure. 14. Determine the total amount of tension reinforcement for the given condition above. 15. Determine the amount of compression reinforcement required.

Situation 5. A rectangular beam with limited size of 300 mm wide is to be designed for an ultimate moment of 550 kN m with f'c = 28 MPa and fy = 420 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. 13. Determine the maximum tensile steel ratio if the tensile steel strain will not be less than 0.005 for a more ductile failure. 14. Determine the total amount of tension reinforcement for the given condition above. 15. Determine the amount of compression reinforcement required.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
A 62.6-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used oy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. B D 1.5 m The smallest allowable dimension dis mm.
4. Find the maximum allowable value of P for the column. The cross- sectional areas and working stresses () are shown in Figure 3. 2P FIGURE 3 Steel: A=500 mm² Qw=120 MPa Timber: A=2000 mm² Ωw =12 MPa Timber: A=8000 mm² Ωw =16 MPa
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moment. Fc'= 40 Mpa.
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Determine the maximum and concrete and steel stresses at the point of maximum positive and negative moments
Put detailed solution and free body diagram. The topic is shear and bearing stresses.
need answers pls and solutions asap, thank you!
A rectangular beam 200 mm wide has an effective depth of 350 mm. It is subjected to a bending moment of 24,000 Nm. The permissible stresses are c = 5 N/mm², t = 140 N/mm²; and m is 18. The required area of tensile reinforcement will be.
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths