Situation 1- For the pin connection shown in Figure S56-021, the allowable shearing stress in the pin is 130 MPa, the allowable bearing stress between the pin at the plates is 340 MPa, and the allowable tensile stress in the rod in 120 MPa. 25. Determine the value of P without exceeding the allowable shearing stress in the pin, in kN. A. 183.8 В. 174.5 26. Determine the value of P without exceeding the allowable bearing stress, in kN. A. 212 kN B. 224 kN С. 196.3 D. 204.7 C. 246 kN D. 168 kN 27. Determine the value ofP without exceeding the allowable tensile stress in the rod. A. 124 kN В. 132 kN C. 115 kN D. 105 kN 30 mm Ø pin 12 mm thick 22 mm thick 35 mm Ø rod Figure S56-021

Situation 1- For the pin connection shown in Figure S56-021, the allowable shearing stress in the pin is 130 MPa, the allowable bearing stress between the pin at the plates is 340 MPa, and the allowable tensile stress in the rod in 120 MPa. 25. Determine the value of P without exceeding the allowable shearing stress in the pin, in kN. A. 183.8 В. 174.5 26. Determine the value of P without exceeding the allowable bearing stress, in kN. A. 212 kN B. 224 kN С. 196.3 D. 204.7 C. 246 kN D. 168 kN 27. Determine the value ofP without exceeding the allowable tensile stress in the rod. A. 124 kN В. 132 kN C. 115 kN D. 105 kN 30 mm Ø pin 12 mm thick 22 mm thick 35 mm Ø rod Figure S56-021

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P = 50 kN is distributed equally among the three rivets, find (a) the shear stress in a rivet; (b) the bearing stress between a plate and a rivet; and (c) the maximum average tensile stress in each plate. P 130 mm 25 mm 25 mm
6
1. THE MEMBERS OF THE STRUCTURE SHOWN BELOW WEIGH 2918 N/M, DETERMINE THE SMALLEST DIAMETER OF PIN THAT CAN BE USED AT A IF THE SHEARING STRESS IS LIMITED TO 34470 kfa. ASSUME SINGLE SHEAR. 1.20 m 1.80m 1,20 M 0.90 m
9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45° Probs. 9-6/7 80 MPa
P7-L In cach case,calculate the value of Q and i that are used in the shear formula for finding the shear stress at A. Alsa, show how the shcar stress acts on a differential volume element located at point A. fa2m 02m tazm al aim (d) al m 03m 03 m taim Fozm le) a5m falm 402m 0.3m talm 01m (c)
0.15
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
Q.17 The maximum bending stress is A - w/m L P Od
الأول لمادة مقاومة المواد Question # 1: Determine the maximum shear stress acting at section a-a in the beam and the shearing stress at the junction of the flange and web plot the shearing stress along the beam. 200 mm 8000 N a 111 1.5 m 1.5 m 150 N/m 4 m G D 50 mm E 400 mm 75 mm 600 mm 75 mm
i need the answer quickly
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
15