ASWARsince 1986DATE:Air entiers300kfate ofratiotemperaturethe the thermal efficiiency of.the Brayton cycleput inthewith Volumetric flow5m²/s10.is 140s k Determinecompeisorthe Compressionthe turbinc in letisthe power outCदि 3D 1.005Kwatt.

Answered: Image /qna-images/answer/ef0049e1-bc26-420e-bc36-bc2d815165a0.jpg

since 1986 DATE: Air enters 300 K rate of ratio temperature the the thermal efficiency of, the Brayton cyclk the power out put in the with Volumetric flow 5m²/s lo. the turbine in kt is 140s k Determine compeisor at the Compression Kwatt . CPa=lo05,8qz44

since 1986 DATE: Air enters 300 K rate of ratio temperature the the thermal efficiency of, the Brayton cyclk the power out put in the with Volumetric flow 5m²/s lo. the turbine in kt is 140s k Determine compeisor at the Compression Kwatt . CPa=lo05,8qz44

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An R22 system has compression raito of 4:9:1 NRE of 72 btu/pd , heat compression of 18 btu/ pd and constant volume of 1.4 cfm at inlet to the compressor . what's the displacement of compressor for 1 ton of refrigerant.
3) The pump works (wbomba) and the turbine (wurbina). 4) The heats: boiler (QH) and condenser (QL). 5) The thermal efficiency of this cycle.
The reheat pressure effect the operating variables and thus turbine performance. Repeat Problem 2 twice, using 0.6 and 1.0 MPa for the reheat pressure For the engine find W and ?? .
1.In a steam power plant, steam enters the turbine at a pressure of 7.2 Mpa and 550°C and exhaust at 20 Kpa. The turbine inlet is 3 m higher than the turbine exit. Inlet velocity of steam 20 m's, and outlet velocity of 100m/s. a) Calculate the required steam flow for a 2MW plant capacity b.) with 90% stage efficiency, find the quality and enthalpy of exhaust steam
Q6/ In Diesel engine the air at the beginning the compression stroke the pressure and temperature 100kpa, 4OC respectively. The compression ratio is 16 and cut off ratio is 2.2. Find the maximun pressure and tempe rature. Heat imput, thermal cfficicncy and thc work down?
An accumulator tank has a capacity of 20MWh. The flow temperature is 110 ° C and the return is 40 ° Cfor the district heating network.a) What is the volume of the accumulator tank when it is full (m³)?
Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 5. A centrifugal compressor has a single stage and 4 stage model with suction conditions of 100 kPa and 25c. The air must be discharged at 300 kPa. Find the compressor work and heat rejected for each model if the compression is isentropic, and the intercooler pressures.
At an isentropic non-flow process of air, the pressure decreases from 62 psia to 17 psia.It has a mass of 0.15 lb and with initial temperature of 275°F. Find the heat transferred,BtuA. 0 B. 100 C. 200 D. 300
5. A single row impulse turbine receives 3 kg / sec steam with a friction etc amount to 15 KW, determine the blading efficiency and the blade velocity coefficient. The nozzle angle is 16° and the blade exist angle is 17°
The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It enters the turbine at a temperature of 1300 K and exits at a temperature of 800 K. Since the power of the gas turbine is 10 MW, a) Draw the T-s diagram of the cycle b) Find the amount of fluid circulating in the installation. c) Find the adiabatic efficiencies of the gas turbine and the compressor. d) Find net work Note. Assume that the specific heat of heating of the air is constant. cp=1 kj/kgC cv=07181 kj/kgC
A petrol engine is having, stroke length of 200 mm and clerance length (clerance gap) of 20 mm. Then the compression ratio of such engine will be a. 12 b. 11 c. 0.01 d. 10
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…