2. Based on the USCS, what is the20 pointspercentage of the gravel in thissample? *SievePercent100Sieve90opening(mm)passing(finer)No.807044.7599.06010294.050200.8567.44030300.651.420400.42539.410600.2523.41400.10613.40.010.11102000.0752.0Particle size (mm)PanO (a) 0 %O (b) 6%O (c) 1%O (d) 32.6%Percent finer by weight

According to USCS, the size of gravel range from 4.75mm-75mm.

Sieve Percent 100 Sieve 90 opening passing (mm) No. 80 (finer) 70 4 4.75 99.0 60 10 2 94.0 50 20 0.85 67.4 40 30 30 0.6 51.4 20 40 0.425 39.4 10 60 0.25 23.4 140 0.106 13.4 0.01 0.1 1 10 200 0.075 2.0 Particle size (mm) Pan (a) 0 % (b) 6% (c) 1% (d) 32.6% Percent finer by weight

Sieve Percent 100 Sieve 90 opening passing (mm) No. 80 (finer) 70 4 4.75 99.0 60 10 2 94.0 50 20 0.85 67.4 40 30 30 0.6 51.4 20 40 0.425 39.4 10 60 0.25 23.4 140 0.106 13.4 0.01 0.1 1 10 200 0.075 2.0 Particle size (mm) Pan (a) 0 % (b) 6% (c) 1% (d) 32.6% Percent finer by weight

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A concrete beam sample has a width of 5 inches, a depth of 6 inches, and a length of 20 inches. The…

Q: Final setting time of cement should not be more than * The setting time of cement - with a --- 30…

A: This question is related to the Cement from Building Material. In this we filled the blanks using…

Q: Thre Plate 1 large plates ane Separzuteel thin layers 2m/s of ter ( M= 1, 02 */o Pais) and 0.1 Water…

Q: What will be the mixing ratio of X aggregate when the following aggregates are mixed in such a way…

A: For the given data We have to find the mixing ratio of X aggregate such that 87% of mixed aggregate…

Q: if the V.M.A 17.37%, bulkGagg 2.65, Actual Gm 2.38, the % for aggregate will be * O 93% 92% O 95% O…

Q: P P [1.75 in. ートーート→ P 5.75 in.

Q: The nominal maximum size for an aggregate is the standard sieve opening immediately smaller than the…

A: Answer:- Nominal maximum size of an aggregate:- The smallest sieve opening through which the entire…

Q: please get a report. I want you to explain to m

Q: What is the maximum diameter of aggregate considering the depth of the slab in cm if the value of d…

A: This question is related to the design of RCC Structure.

Q: The rods Shown have a diameter of lisin.and is a gae temperature is increased oy f00, determine of…

A: Given Diameter,d=1.5inch Increase in temp,∆T=100°/F LB=10inch LAl=5inch

Q: Load (N) Deflection (mm) 0 0 4.903034 0.000346 11.416539 0.000802 18.337648 0.001251…

A: The data you provided is from a load-deflection test on a mortar specimen. It shows how much the…

Q: The diameter and length of the tamping rod are _mm and mm in the Aggregate Impact Value Test. А.…

A: Aggregate impact value test is used to measure the toughness of aggregates. In this test aggregates…

Q: 50- Vibration compasted Hand compacted Compressive Strength (28 days) MPa 15 0.6 Waterlcement Ratio…

Q: QI: Justify the following: c. In practice, the engineer could not make use of the absolute and bulk…

A: Specific gravity is helpful in the measurement of the strength of the aggregate. Higher the value of…

Q: For Coarse aggregate- Gyesis Oven Dry woight (W.) = 34609 (A) 2ot Saturated Surface Dry (SSD)= 3500g…

Q: Compute the mass fraction of a ferrite and cementite in pearlite.

A: Lever rule: - It is defined as the rule that helps to find mass fraction of every phases.

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: Betermine the volume V and total surface area A of the solid generated by revolving the area shown…

Q: What is the cumulative percent retained on the sieve with the highest percent retained? (2 decimal…

A: We will take average of all three trials and find the cumulative percent retained.

Q: A. The temperature when the gab close B. The stress in Aluminum when temperature reaches 140°F

Q: A core cutter of 130 mm height has inner and outer diameters of 100 mm and 106 mm. respectively. The…

Q: 3. Determine the normal force between the crate and the surface 4. Determine the force P needed to…

A: Given- W = 856 N Frictional coefficient - μs = 0.3 height of block = h = 2 m Width of block = b = 1…

Q: Q1- The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length…

A: Stress: Stress is defined as the deformation offered by internal resistance. it is also defined as…

Q: civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3…

Q: P 1 m W = X N 1 ms = 0.4 5. Determine the normal force between the crate and the surface 6.…

Q: Q2. Calculate the CBR value for the laboratory data in the table. Load (kn) Penetration (mm) Mold…

Q: Design Average Strength Strength (MPa) Specimen Diameter Batch No. Strength Age (days) (Mpa) Load…

Q: 1- The reason of place the weights over CBR sample to ......curve 2- The relationship between…

Q: : 200 Gla A ABC 200 mm C D ABC Eco: 100 dra A pc A: 2 00 mm = lo0 mm 10ON BCD is sCEwed into ABC…

Q: Civil Engineering help Table 1 Test No. Avg. sample length (mm) Rate of Avg. sample diameter (mm)…

A: What to determine was not mentioned clearly, please provide the full question. I just circled the…

Q: 2. What do the various elements that comprise the gating system? What are the function pouring basin…

A: As per guidelines we are supposed to answer only first questions, so please repost rest questions…

Q: MB 2 TEST 2: SPLITTING TENSION TEST (BS EN 12390-6: 2009) Table 2. Result of Splitting Tension Test…

A: given- Tensile splitting strength-for specimen 1Fct=4.28 MPafor specimen 2Fct=3.35 MPafor specimen…

Q: procedure of sieve of coarse aggregates.

A: SIEVE ANALYSIS Sieve analysis is helpful in determining the particle size distribution of the…

Q: kiv A E = 200 GPA deformation BC deformationn AB total defomatiom of ABCD 5.34 mm O -5.34 mm -0.88…

A: Calculate deformation of AB,BC and total deformation?

Q: What will be the diameter of an indentation in (mm) to yield a hardness of 250 HB when a 500-kg load…

A: Given data: Hardness number=250 HB p=500 kg. sphere diameter=5 mm

Q: Internal diameter and depth of cylindrical steel cup are mm and mm in Aggregate Impact Value test.…

A: aggregate impact value test setup

Q: A box measuring 50 cm x 50 cm × 50 cm is filled to the top with dry coarse aggregate of mass 187.5…

Q: A vinyl [E = 2.65 GPa; v = 0.42] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm…

Concept explainers

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.

Question

2. Based on the USCS, what is the
20 points
percentage of the gravel in this
sample? *
Sieve
Percent
100
Sieve
90
opening
(mm)
passing
(finer)
No.
80
70
4
4.75
99.0
60
10
2
94.0
50
20
0.85
67.4
40
30
30
0.6
51.4
20
40
0.425
39.4
10
60
0.25
23.4
140
0.106
13.4
0.01
0.1
1
10
200
0.075
2.0
Particle size (mm)
Pan
O (a) 0 %
O (b) 6%
O (c) 1%
O (d) 32.6%
Percent finer by weight

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please show how to graph following data, thanks
Q1) Read the following sentences, write true or false, and correct the sentences that are false: 70, and by 20% 111 I Ultian vanas Ol Yu 3- The alkali silica reaction is very fast, happen between active silica in the cement and the alkalis in aggregate. Call wings: [5M] 4- Sulphate in mixing water should not be more than 10,000 ppm. 5- Higher curing temperature decrease earlier strength, but it increases 28-day strength of concrete.
@ solved®x([n(x)=n(y))dy=ydx=0
A 2000 g coarse aggregate sample in SSD condition weighed 1272 g when immersed in water. The same sample when dried in oven weighed 1984 g. Calculate the SSD bulk specific gravity, apparent specific gravity, absorption capacity and dry bulk specific gravity of the aggregate. 3 Ca 15:38 5EEהבןה F5 F6 F8 F9 F10 F11 F12 PAT SC PAUSE DEL END INSERT BREAK ). 9] %3D -> Sv2 O} NUM BACKSPACE T Y P 7 ENTER HOME G H K L B 1 SHIFT END すv :0
None
Do not give answer in image and hand writing
Discuss the different sources of size effect. Describe energetic size effect in fractureusing two different sizes of a plate with a center notch. Explain the significance of platethickness.
How many grams (whole number, no need for unit) of fine aggregates used in this experiment? Blank 1 Blank 1 Add your answer
Us Standard Sieve No. Sieve Opening (mm) Weight Retained (g) % Retained on Sieve % Passing Sieve 4 4.75 12.7 6.2 93.8 10 2 24.8 12.1 81.7 20 0.85 21.5 10.48 71.24 40 0.425 38.8 18.92 52.33 60 0.25 23.8 11.60 40.73 100 0.15 19.5 9.51 31.23 200 0.074 46.7 22.76 7.463 Minus 200 17.3 8.44 0 Total 205.1 for D10 and D60 calculate the k value utalizing Hazen's approxoimation. c=100
do not round off in between solution
5
Show complete solution pls X=646 Y=46 A=8 B=7 C=8