Sieve Apperture (um) Weight Retained, (g) Weight of ore = 500 g 100 50 200 150 125 100 75 45 What is the percentage composition material between 200 and 180 um? 68 80 Were there some material losses? What 20 accounts for such an observation? 60 100 20 30 Pan

Q: A h Ph³ 351 PROVE THAT A = Ph 361 BY: CONJUGATE BEAM METHOD →THREE-MOMEN EQUATION SLOPE DEFLECTION…

A:

Q: Define the role of packing materials in the pipe jacking of concrete pipes.

A: Packing materials are about 10mm - 20mm thick and these are generally made of the plywood,the…

Q: For the given beam, draw the simplified free-body diagram and below it the shear and bending moment…

A:

Q: Consider the beam shown in (Figure 1). The members are pin connected at E and F. Suppose that P =…

A: Using static equilibrium conditions, summation of moment at F = 0, ( Because, there are only…

Q: Show step by step solu

A: Q=1.555D2Explanation:

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

A:

Q: Derive a mathematical relationship describing the calibration curve.

A: Using Bernoulli's equation : Bernoulli's equation states that sum of pressure head plus datum head…

Q: Give the purpose of having Sieve analysis of Aggregates

A: A sieve analysis determines the distribution of aggregate particles by size within a given sample.…

Q: How to conduct a rebar tensile strength test?

A: Introduction : A sample is typically tugged to its breaking point in a simple tensile test to…

Q: 2. IN THE SYSTEM SHOWN, THE COEFFICIENT OF FRICTION BETWEEN BLOCK A AND THE PLANE IS 0.25. NEGLECT…

A:

Q: The mass of body A is 45 kg. The coefficient of friction for bodies A, B, and the ramp C is 0.10.…

A:

Q: How to prepare samples and perform thermal expansion tests ASTM E831? b) how to perform tensile…

A: Testing materials are an important component of understanding their physical properties, helping in…

Q: Estimate and draw the centroid of the shaded area wit respect to the coordinate axes shown în Figure…

A: To find centroid of section

Q: A distance of 300 m is to be laid-out using a tape having an incorrect length of 29.98 m. How much…

A: Given, Distance to be measured, say D = 300 m Actual/incorrect length of tape, L' = 29.98 m   To…

Q: How to prevent retained austensite

A: By controlling the below parameters we can prevent retained austensite. It is very necessary in…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

A:

Q: For the composite area shown, calculate the location of centroid with respect to reference X and Y…

A:

Q: Show the relation between modulus of elasticity and bulk modulus.

A: Bulk modulus :k=StressVolumetric strain=σδVVYoung's modulus :E=StressLinear Strain=σεWe know…

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: 2) An 8m steel tape was purchased and advertised as follows: Standard temperature Standard Pull Таре…

A:

Q: STATICS For the figure shown, if the resultant of the forces is acting at the slab center, O O 10…

A:

Q: Estimate and draw the centroid of the shaded area with respect to the coordinate axes Shown in…

A:

Q: Determine the forces in each member and the reactions at the supports. Indicate whether the members…

A:

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

A:

Q:  please provide me with the step-by-step solution

A: Given: SystemDollar (Cost)TonMinuteDollar per ton per…

Q: Why is space filled with grout in this image necessary? Column Bar Plate Top Nut Grout Bottom Nut…

A: We know that grouting is generally used to fill the voids or  space between the two surfaces so that…

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the results in…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Describe Consistency in the Remolded State and Plasticity.

A: Consistency Limit:

Q: DETERMΙNI R AND MOME 8-FT RVAL START T A AND DE R RAM AND FOR QUND BEAM A IGURE. ASSI ORTS AT A…

A:

Q: Find the percent finer of each sieve.

A: % finer for each sieve =Total wt-Cumulative wt retained upto that sieveTotal wt% finer for sieve 4…

Q: For the box section shown in Fig. 5, find the yielding moment M, the plastic moment M, and the shape…

A:

Q: A SOLID ALUMINUM SHAFT 2 INCH DIAMETER IS SUBJECTED TO TWO TORQUES AS SHOWN IN THE FIGURE. DETERMINE…

A: Given data: Diameter of shaft=2 inch Torque=T1=200 lb-ft T2=800 lb-ft It is asked to find maximum…

Q: allowed.

A: Given data- Diameter of the solid segment 1 d1 = 41 mm= 0.041mDiameter of the solid segment 2 d2 =…

Q: The sign has a mass of 100 kg with a center of mass at G. Determine the components of the reaction…

A: The mass of the sign = 100 kg The weight of the rod AB is to be neglected To determine:- The…

Q: Based on the survey notes below, fill in the necessary data to answer the next set of questions. All…

A: Reduced level :- Elevation of a point with respect to mean sea level is called Reduced Level.Back…

Q: Draw the Stress-Strain Diagram and label it properly.

A:

Q: FORMULA: The formula for calculating the water content for Plastic limits is as follows: W1 – W2…

A:

Q: Explain Cross section of portland cement concrete showing cement paste and aggregate particles.

A: Portland cement concrete:- High-strength concrete produced from Portland cement is highly…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A: