At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M = 201 mm. Round off the final answer to four decimal places. d L M Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C B Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C

At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M = 201 mm. Round off the final answer to four decimal places. d L M Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C B Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 A 0.5 mm 250 mm 300 mm B Magnesium A = 2000 mm² E=45 GPa α = 26 X 10-6/°C Aluminum A = 800 mm² E = 75 GPa a = 23 x 10-6°C 5 pts At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120°C. (a) The normal stress in the aluminum rod (MPa) =
A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. If the system is initially stress-free. Calculate the temperature change that will cause a tensile stress of 80 MPa in the brass rod. Assume that both rods are subjected to the change in temperature. Brass L-2m A= 1200 mm E- 100 GPa a18.7 um/(m*C) 3m 2m- Copper L-3m A= 1500 mm E= 120 GPa a = 16.8 um/(m"C)
At room temperature, a 0.6-mm gap exists between the ends of the rods as shown in Figure Q2 (a). At a later time when the temperature has increased by 120 degree Celsius, determine the followings: 0.6 mm 350 mm- ks A w B Figure Q2 (b) - 300 mm A Aluminum A = 2000 mm² E = 75 CPa Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C a = 23 x 16-6/°C Figure Q2 (a) a.) Calculate the support reaction R due to the increase in temperature b.) Calculate the stress and change in length of the stainless steel rod c.) If the rods are connected through the gap with a spring having spring constant ks = 10x10⁹ N/m as shown in Figure Q2 (b), recalculate the reaction R when the increase in temperature is 60 degress Ce is. B
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the normal stress on the steel due to the change in temperature. Steel Brass Copper Est = 200 GPa ast = 12(10-)/°C abr Ebr = 100 GPa 21(10-")/°C acu = 17(10-")/°C Ecu 120 GPa %3D %3D Acu 515 mm? 200 mm? Abr = 450 mm2 Ast -300 mm -200mm 100 mm O 20.11MPA, C O 15.57MP., C O 8.94MPA, c O 35.02MPA, C
A copper tube having a cross sectional area of 2000 mm2 and a length of 300 mm is rigidly fixed to two rigid caps on its longitudinal ends. Four steel bolts, each having a diameter of 22 mm, are symmetrically arranged parallel to the axis of the tube and are slightly fastened to the rigid caps, as well. The temperature of the assembly is then raised to 70oC. Take the elastic modulus for Copper and Steel as ECU=100 GLa and EST=200 GPa respectively; the coefficient of linear expansion for Copper and Steel as aCU=16x10-67°C and aST=12x10-6/°C respectively. Calculate the load carried by the copper tube and the load carried by each steel bolt
3. A steel bolt through a 25-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross-sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 10^6 psi, coefficient of thermal expansion = 6.5 x 10^-6 per degree Fahrenheit. For aluminum: E = 10 x 10^6 psi, coefficient of thermal expansion = 13.0 x 10^-6 per degree Fahrenheit. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places. ) * Your answer This is a required question Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) * Your answer This is a required question Find the stress (in psi) induced in the steel bolt by the temperature change. * Your answer
The rigid bar 2 m long is supported by a steel rod at the middle B and bronze rods equidistant from both ends at A and C as shown. The properties of the rods are given in the tabulation below. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity, E 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1,000 mm What is the required length of the steel rod so the reactions on the three rods are the same? What is the required length of the steel rod so that both the steel and the bronze rods reach their allowable stresses at the same time? What is the maximum permissible load W that the rods can carry?
F2. Figure Q2 shows a straight rod of circular cross section, of diameter 20 mm, length 0.8 m and made out of copper. The rod is rigidly supported at one end while the other end is free to be displaced a distance of 0.5 mm. Take the elastic modulus of copper E = 117 GPa. The drawing is not at scale. a) If the coefficient of thermal expansion of copper is 17x106 °C1 find the temperature change AT which causes the end B of the rod to touch the wall. b) What is the reaction force at end B if the temperature increases with 2AT? c) What is the temperature increase which causes the rod to buckle elastic? Assume pin joint conditions at end B. d) If the rod was rigidly supporter at both ends, what is the temperature raise needed to cause elastic buckling in the rod? B 0.8 m s = 0.5 mm Figure Q2 D = 20 mm
A circular steel rod AB (diameter d1=15 mm, length L1=1100 mm) has a bronze sleeve (outer diameter d2 21 mm, length L2=800 mm) shrunk onto it so that the two parts are securely bonded (see figure). Calculate the total elongation δ (mm) of the steel bar due to a temperature rise ΔT=200oC. (Material properties are as follows: for steel, Es=210 GPa and αs=12x10-6/C; for bronze, Eb=110 GPa and αb=20x10-6/C.)
At a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.
A steel bar is connected to an aluminum bar as shown below. At 70 F, the stresses in the steel and the aluminum bars are zero. Calculate the stresses in the steel and in the aluminum when the temperature rises to 120 F. Indicate whether the stresses are tensile or compressive. The properties of the steel and the aluminum are given below. The cross-sectional areas of the steel and the aluminum are the same.
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm