Shafts AC and DE have 50 mm radius and shear modulus G=79.3 Gpa. 60 kN.m Torque is applied to end E and 25 kN.m Torque to gear D .Find the angle of twist of at E of shaft DE. Please consider the twist directions.

Q: he two solid steel shafts shown in the figure are connected by gears. Determine the angle of twist…

A: Given  Shear modulus, E = 70 GPa              Torque, T = 25 N           Diameter, d = 20 mm Find…

Q: The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at…

A: Given data as per question Diameter of shaft =2.5 in Length of shaft =2 in Torque applied =750 lb.in…

Q: The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and…

A:

Q: Find the torque and power transmitted by a 100 mm diameter shaft, if maximum angle of twist and…

A:

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: 4 mm module 20° full-depth The gear shown above is to transmit 1 kW at a speed of 200 rev/min. Find…

A:

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: This engine is used in a hoist. Motor 2.5 kW with the help of gears with a power of and n = 500 rpm.…

A:

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: For the shaft shown in the figure below, compute the angle of twist of pulleys B and C relative to…

A:

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: A torque of 36-kip-in. is applied on an aluminum shaft as shown in the figure. Use G = 3.7 × 106…

A: The value of the torque,(T)= 36 kip-in.The shear modulus of the material, (G)=The length of the…

Q: A circular shaft with diameter 50mm and its length is 850mm long and is made of steel,The shaft is…

A:

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

A:

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

A:

Q: A steel shaft ABCD having a total length of 3.5 m consists of three lengths having different…

A: Torque is the rotational equivalent of linear force. It is also referred to as the moment, moment of…

Q: A B 55² 240 N.mm 420 N.mm 300 N.mm 480 N.mm Figure 1 - Torques applied to the driveshaft 1) DERIVE…

A: Find the  Angle of twist expression Shaft diameter Maximum shear stress

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: A shaft has an external diameter (ED) of 350 mm and an internal diameter of 150 mm.…

A: Given that, External diameter of shaft, D=350 mm,Internal diamter of shaft, d=150 mm,Length of…

Q: hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate…

A:

Q: A T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable…

A:

Q: The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a…

A: Rotating shafts are used for different types of power transmission applications. The most common…

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each…

A:

Q: The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: esign a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of…

A: Given: Hollow shaft,Power,P=80 kWspeed, N=4000 rpmangle of twist,θ=0.2oshear stress, τ=480…

Q: A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB.…

A: Consider a shaft having radius R is subjected to a twisting moment T. Then, shear stress developed…

Q: Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point…

A: In order to obtain the angle of twist at point a, we must use the relation as given below: TJ=ςr=Gθl…

Q: A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The…

A: Given: ϕA=ϕA/D=-0.382radϕA/B=0.358radϕB/C=-0.233rad

Q: A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and…

A: The power transmitted, P = 100 kWThe speed of shaft, N = 180 rpmThe allowable stress = 50 MPaThe…

Q: Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The…

A:

Q: When a solid steel shaft is subjected to a torque of 45,000 in-lbs, the maximum shear stress is…

A: The given question is solved by using Torsion equation. The value of Modulus of rigidity is not…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.