A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.

Q: A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear.…

A:

Q: Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm…

A:

Q: e diameter

A: To find Outside diameter(d2)

Q: The outside diameter (in mm) of the 10/14

A: Given; A hollow shaft;  length,l=1m  Max permissible twist in the shaft is=10  Inner dia of the…

Q: A solid shaft with diameter 3 in. is to transmit 139 hp. If the shaft shownis rotating at 300…

A: Given      Power, P = 139 hp Diameter, d = 3 in = 0.0762 m     Speed, N = 300 rev/min Find   Shear…

Q: Compute for the diameter in inches of a conveyor head pulley SAE 4130 solid steel shaft being driven…

A:

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: d-150 mm d,-300 mm 4,4 kN 4 B 150 mm KSAN 300 mm 300 mm

A: When an external force is applied to an object and when that force tends to bend the object is…

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: A shaft is fixed at support C and has a torque of 75lb.ft  with respect to free end at a distance of…

A: givenM1=75lbft  at 0.75ft  from fixed end CW2=1200lb/ft M2=600lbft at free end

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

A: Find the maximum torque .

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A: Given:Torque acting at A, TA=105 N.mTorque acting at B, TB=314 N.mTorque acting at C, TC=372…

Q: pot

A:

Q: Determine the minimal value of a radius of the circular-solid shaft in problem 1 such that the…

A:

Q: Calculate the maximum allowable torque (in-lbs). A solid steel shaft is made from AISI 1045 steel,…

A: Given data: - The diameter of the solid shaft is d = 9.0 in. The length of the solid shaft is L =…

Q: Compute the twisting and bending moments of the shaft (AISI 4140 steel) given the following…

A:

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

A:

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3°…

A: Given data:- Angle of twist =3° Length of the shaft =6 m Torque applied =14 kN-m. G = 83 kN/m2 To…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: Design and draw a cast iron flange coupling for a mild steel shaft transmitting 80 kW at rpm with…

A: solution  CAST IRON FLANGE COUPLING Power transmitted P=80kN speed N=220rpmallowable shear stress in…

Q: A SOLID 1.8 IN. DIAMETER SHAFT IS UTILIZED TO SYNCHRONIZE MULTIPLE MECHANISMS IN THE MANUFACTURING…

A: Given: The diameter of the solid shaft is d=1.8 in. The torque delivered by the shaft is T=3500…

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: Compute for the normal shear stress in ksi for a 3.1 inch diameter shaft that is subjected to a…

A:

Q: 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt…

A: (A) Write the given data. w=200 mmP=60 kWv=25 m/sm=2 kg/mC=6 mD=300 mmd=900 mm

Q: A 63.5 mm shaft having a yield point of 50 ksi with a ¾ inch width key. Compute the length of key…

A:

Q: what is the polar moment of inertia (in^4) of a solid shaft that has a torque of 2Kn-m and a stress…

A:

Q: A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The…

A: Given: P = 50 HP N2 = 225 rpm C = 500 mm    (given unit not clear so taken as mm) Transmission…

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and…

A:

Q: Estimate the shaft diameter required to produce a critical speed of rotation of 638 rpm for a steel…

A:

Q: required that a shaft be designed to accommodate a step as indicated. The shaft is to be exposed to…

A:

Q: shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is…

A:

Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…

A: Given, Length of shaft = L = 1 m Power transmitted = P = 30 kW = 30 x 103 W Shaft RPM = 700 rpm…

Q: Select the diameter for a solid steel shaft that is to transmit 60 HP at 850 rpm without exceeding…

A:

Q: (3) For the shaft shown in the Figure, compute the maximum torque T that can be applied., B T…

A:

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.