sentences: 8) The primary mmf is not equal and same direction to the secondary mmf in an ideal transformer. 9) The open circuit test is conducted at the rated current and the short-circuit test performed at the rated voltage. 10) The short-circuit test is performed on low voltage side and The open circuit test is on the high-voltage side. 11) The copper loss is not affected by the load and the core loss varies with the load. 12) Shunt field winding have a large number of turns compared with a series field winding. 13) The voltage regulation of generator A is 10% and that of generator B is 5%. The generator A is better than generator B. 14) The external characteristic of a dc generator is affected by armature reaction. 15) The commutating poles or interpoles is connected in parallel with the armature. 16) The de motor should be started by impressing its rated voltage across the armature terminals. 17) The cumulative compound motor has the advantage of over a series Motor. 18) The torque in a differential compound motor increase and its speed is decreased with an increase in the armature current. 19) The flux in a machine does not vary with time. 20) After m

sentences: 8) The primary mmf is not equal and same direction to the secondary mmf in an ideal transformer. 9) The open circuit test is conducted at the rated current and the short-circuit test performed at the rated voltage. 10) The short-circuit test is performed on low voltage side and The open circuit test is on the high-voltage side. 11) The copper loss is not affected by the load and the core loss varies with the load. 12) Shunt field winding have a large number of turns compared with a series field winding. 13) The voltage regulation of generator A is 10% and that of generator B is 5%. The generator A is better than generator B. 14) The external characteristic of a dc generator is affected by armature reaction. 15) The commutating poles or interpoles is connected in parallel with the armature. 16) The de motor should be started by impressing its rated voltage across the armature terminals. 17) The cumulative compound motor has the advantage of over a series Motor. 18) The torque in a differential compound motor increase and its speed is decreased with an increase in the armature current. 19) The flux in a machine does not vary with time. 20) After m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Only detailed descriptionand and complete answer is required.
A transformer has 600 primary turns and 300secondary turns. The primary and secondary resistances are 0.35 and 0.09 respectively and the corresponding leakage reactances are 1 and 0.08 respectively. Determine (a) the equivalent resistance referred to the Secondary winding, (b) the equivalent reactance referred to the Secondary winding, (c) the equivalent impedance referred to the secondary winding, and (d) the phase angle of the impedance.
A transformer having a nominal voltage = 399V and a no load voltage = 420V at its secondary, the short circuit current at the secondary of this transformer in function of its nominal current will be: Select one: Isc=10*In None of these Isc=30*In Isc=20*In Isc=40*In
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
Q14/ Complete the blank The efficiency of a transformer is maximum when..........................................?
Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)
i need ans within 15 minutes my best wishes ton
4. What are the advantages of Delta connection in high power transformer?
Q2/ Complete the blank A single-phase transformer is rated at 50 kVA. The transformer has full load copper losses of 450 W and iron losses of 150 W. The transformer efficiency at 1/4 th of the full load and 0.95 power factor is...............................................?
Fast do...
don't copy
Q7/ Complete the blank The copper loss of a transformer at 4/5 of the full load is 4000 W, full load copper loss will be..........................................?