FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondaryvoltage is Vs = 42V and output power of the transformer is PN= 2750W.The value of loses powers are Pcu = 52,5W and Pre = 39W. The resistance of loads are RLI = 1,660 andR12 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determinethe following values in the circuit:PrimarywindingSecondarywindingN, turnsNg turnsMagneticFlux,PrimarycurrentISLSecondary4 currentPrimaryvoltageISL1(ISL2SecondaryvoltageRL1R12TransformerCore(a) the primary voltage VP,(b) the secondary load current Isı, if the transformer is rated at RLI and R12,(c) the primary load current IpL,(d) the load resistance R13 when the transformer is fully loaded by third in parallel,(e) efficiency n (fully loaded)

(a) In the question following data is given Np=720 Ns=144 Vs=42 volt Vp can be found by following…

FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondary voltage is Vs = 42V and output power of the transformer is Py= 2750W. The value of loses powers are Pcu = 52,5W and PrE = 39W. The resistance of loads are RL = 1,660 and RL2 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit:

FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondary voltage is Vs = 42V and output power of the transformer is Py= 2750W. The value of loses powers are Pcu = 52,5W and PrE = 39W. The resistance of loads are RL = 1,660 and RL2 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

As given in the figure, an ideal transformer feeds a load under 120V voltage. Which of the following is the source voltage (Vs)?
14. The maximum flux of a 50H2 transformer is 0.001Wb. If the primary is wound Vwith 1080 turns, find the applied primary voltage and then calculate the number of turns required for a 15V secondary. Ans: N2=67
A 50Hz, single phase transformer has a ratio of N2:N1 = 0.2. On full-load, the secondary current is 200A. The resistance and reactance of the primary winding are 0.8 ohm and 4 ohm respectively. The corresponding values for the secondary winding are 0.04 ohm and 0.1 ohm. If the secondary is short circuited, what voltage must be applied to the primary to produce full-load current? What will be the copper loss?
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 14.9-0-14.9 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, RL D2 32.63 21.07 42.14 O26.97
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
3. An ideal transformer with a 500 turns primary and 125 turns secondary windings delivers 400W to a 40 load. The resistance of the primary windings is 16O. Find the primary current and voltage
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
The maximum efficiency of a 200KVA, 6000/230volt, 50HZ, single phase transformer occurs at half load and is 95% at unity power factor. What is the full load efficiency at 0.7 power factor?
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It converts AC signals into DC signals. O It changes the magnitude of AC signals. hp