Select the lightest S section that will safely support the service tensile dead load of 75 kips and the service tensile live load of 40 kips. The member is to be 20 feet long and is assumed to have one line of holes for 3/4" diameter bolts in each flange. Assume that there is at least three holes in each line 4- in on center. Use A36 steel.

Select the lightest S section that will safely support the service tensile dead load of 75 kips and the service tensile live load of 40 kips. The member is to be 20 feet long and is assumed to have one line of holes for 3/4" diameter bolts in each flange. Assume that there is at least three holes in each line 4- in on center. Use A36 steel.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.1P

See similar textbooks

Similar questions

SOLVE FOR1 HR
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by ¾ inch boltas shown below. Use A36 steel with Fy=36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD
Asap pls
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
A tensile member consists of 2 ? 4 × 3 × 1/2 carries a service dead load of 50 k and live load of 100 k, as shown in Figure P13.15. The angles are welded to a 3/4-in. gusset plate, which is welded to a column flange. Design the connection of the angles to the gusset plate and the gusset plate to the column. The gusset plate is connected to the column by a CJP groove, and the angles are connected by a fillet weld. Use E 70 electrodes. The steel is A572. FIGURE P13.15 Welded connection for Problem 13.26. L4 x 3% 3-in. gusset plate Design welded connection 40⁰
A double-angle tension member, 2L 3 x 2 x 4 LLBB, of A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is connected to a gusset plate with one-line of 3/4-inch-diameter bolts through the long legs. Does this member have enough strength? Assume that A₂ = 0.85An. Ae Use LRFD. Use ASD. 1 2 IL Section CIVIL ENGINEERING STEEL DECIGN
A bracket cut from a W310X179 is connected to a W310X179 column flange with 12 A325 bearing-type bolts as shown in the figure. A 50 steel is used. The line of action of the load passes through the center of gravity of the connection. What size bolt is required? a. Use LRFD. b. Use ASD. D = 55k L = 145k I'-1" CS Scanned with CamScanner 22" 5 sp @ 4" て

Tension member
Group A bolts are used in the connection in Figure . Use an elastic analysis and determine the required size if slip is permitted. The 10kip load consists of 2.5 kips of service dead load and 7.5 kips of service live load. All structural steel is A36. a. Use LRFD. b. Use ASD.
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.