Select the correct order of steps in the drop down lists below for the graphical analaysis method to determine the area required at the throat of a nozzle flowing a condensable vapour for a given set of iniet and exhaust conditions 1 Cick for List 2 Calculate the area per unit mass flow rate 3 Determine the specific volume at each intermediate pressure Determine the specific enthalpy at each intermediate pressure 4. Plot a chartigraph of showing the variation of area per unit mass flow rate against pressure Locate the minimum to determine the approximate throat location and critical pressure 6. Determine the value of dryness fraction at these intermediate pressures 7. Divide the change of pressure into a number a pressure steps

Select the correct order of steps in the drop down lists below for the graphical analaysis method to determine the area required at the throat of a nozzle flowing a condensable vapour for a given set of iniet and exhaust conditions 1 Cick for List 2 Calculate the area per unit mass flow rate 3 Determine the specific volume at each intermediate pressure Determine the specific enthalpy at each intermediate pressure 4. Plot a chartigraph of showing the variation of area per unit mass flow rate against pressure Locate the minimum to determine the approximate throat location and critical pressure 6. Determine the value of dryness fraction at these intermediate pressures 7. Divide the change of pressure into a number a pressure steps

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly answer correctly. PPlease show the necessary steps
Editing Q1. Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The cylindrical fin has a diameter of D 20 mm, and cross-sectional area is the same for each configuration shown in the sketch. V, T, V, T, V, T. Configuration A Configuration B Configuration C For fins of equal length and therefore equal mass, which fin has largest heat transfer rate? %3D Assume the gas properties are those at T (treat it as air) = 350 K. Hint: Assume the fin can be treated as infinitely long. D Focus stes)
I need answer within 20 minutes please please with my best wishes
I need the answer quickly
all parts please tyyyy
THE PROBLEM IS FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at the boiler inlet), is superheated to 100 degrees SH at the same pressure. Flow rate is at 10 cubic meters per minute. Ans.: a) Qa = b)Wsf= Hint: Use v at compressed water temp. at boiler inlet to convert to mass flow rate. Process is isobaric (Constant Pressure, where Q=m x AH).
The concentration of salt ? g/L in homemade soap is given as a function of time as follows: ??/dt = (0.37? − 0.03)? At the initial time, ? = 0 minute, the salt concentration is 20 g/L. Choose a step size in a range of 1 < h ≤ 1.5 minutes for the interval from 0 to 8h minutes and apply THREE (3) numerical methods to compute the salt concentration. Select the best numerical method to estimate the salt concentration and justify your answer. method 1: ruler's method
Perform a simple mass balance on the completely mixed reactor below to identify the recycled sludge concentration, X, as a -- I -- function of the recycle ratio, R, and the mixed liquor concentration, x. Draw the system control boundary across which your mass balance is performed. a. b, Set-up your mass balance equation. Make sure to clearly identify inflows, outflows, rates of growth/consumption, etc., within your system; Identify ALL assumptions; c. d. e. Solve your mass balance equation for the recycle sludge concentration; If your recycle ratio, R, is 45% and your wasting rate is 5% of the average daily flow, what is the expected recycle sludge concentration, X, with respect to the mixed liquor concentration, X? Influent Effluent Clarifier WAS RAS Completely mixed reactor system
The below results are for cooling tower expirement, energy balance :energy balance of the system, that is to say, the energy taken by the air must be equal to the energy supplied by the water flow. Question : Discuss the tabulated cooling tower results... Discuss in detail format!
Argon enters a steady-state throttle valve ata pressure of 300kPaand a specific volume of 0.55m*/kg. What is the exit temperature if the exit pressure is 100kPa Report your answer using units of Kelvin and to three significant digits. Do not round numbers used in your computation. Only round the final numericanswer,
Please help me, please, I want to solve all the questions, without quoting and without plagiarism, I want the solution in MS Word, I do not want handwriting...