Safe stress for the steel bar shown in the figure is sigma(safe)= 160 MPa. According to The greatest shear stress (Tresca) and Von Mises hypotheses a)By neglecting the cutting effect b)Taking shear effect into account Check whether this rod bears the given load.

Q: The load on square section bar consists of a transverse shear force of 12 kN together with an axial…

A: Given: P=20 kNFt=12 kNσy=260 MPaf=1.8ν=0.28

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

A:

Q: he primary and secondary shear loads on bolt P

A: Given; A steel bar of;  =  10×50 mmCantilevered with two M12 bolts,To support a static load of 4kN…

Q: The 0.06R (mm)-diameter bar is made of a brittle material with the ultimate strengths of 0.15R MPa…

A: d=.06R mm where R=993 d=.06×993=59.58 mmσut=.15R Mpa σut=.15×993 Mpa=148.95 Mpa Bending moment and…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by Se has a diameter of 6…

A:

Q: A round cross-sectional bar d= 30 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a…

A: The ultimate tensile strength (UTS) of a material is the highest stress it can withstand when…

Q: Problem 2 Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze…

A: Answer: The total elongation of the bar : ∆Ltotal = ( -7.517 × 10-5 × P ) mm  where, P is in…

Q: (D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates…

A: Given data: Total load (P) = 15 kN                    d = 16 mm                    E =80 GPa Need to…

Q: (8) A tension member subjected to a load of 30,000 lb has a cross section % in. by 6 in. and is…

A: given; load(P)=30000lbcross section hole diameter (d1)=6 inpiercing hole diameter(d2)=1 infactor of…

Q: sectional bar d= 39 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a completely…

A:

Q: A round cross-sectional bar d= 32 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a…

A: d = 32 mm Sut = 715 MPa Se = 350 MPa

Q: Determine the number of life cycles for an alternating stress of 70 ksi. Select one: a. N = 1.66E+05…

A:

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

A: Q) Given data         σx = 170 MPa        σy = 90 MPafor AISI 1020  carbon steel σyt = 350 MPaTo…

Q: Please please try to solve it asap it is too urgent. A solid round bar, 25 mm in diameter, has a…

A:

Q: A metal hollow shaft is subject to a tensile load of 53kN and a positive torsional moment (right…

A:

Q: The composite bar, firmly attached to unyielding supports, is initially stressfree. What maximum…

A:

Q: A circular rod of hot-rolled 4340 steel (4340-HR steel - 4mm diameter, 1.35m long) is subjected to a…

A: Given Data:- 4340 Steel  Diameter=4mm Length=1.35m Modulus of Elasticity=207Gpa Yield-Strength…

Q: FIND THE AREA USING SODERBERG PRINCIPLE

A: Given data; P1=20 kNP2=100 kNσyt=240 MPaσe=160MPaF.O.S=2

Q: The wood beam in (Figure 1) is subjected to a load of P = 15 kN. Grains of wood in the beam at point…

A: Given data with the suitable variables. P=15 kNβ=25°   It is required to determine the normal and…

Q: Compute the Cracking moment of the T-beam shown in the figure Using the Design parameters given bf…

A: Given dataf'c=28MPafy=275MPa

Q: and also find the fillet radius(r) Take theoretical stress  concentration factor as 2.5.  Also find…

A:

Q: Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The

A:

Q: steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In…

A:

Q: 1) Find the allo wable safe loacd Pif the stresses in the bar are the following BC = 60 ksi AB = 50…

A: σAB= 50 ksiAab=.6 in2σBC=60 ksiAbc=.3 in2σCD=70 ksiAcd=.4 in2

Q: Figure 1: This bar is made of AISI 1020 cold-drawn steel and is loaded by the forces F=60 lb, F2= 80…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

A: Given Data  σx = 199 MPa σy = 76 MPa

Q: hardest point in the embedment A or B of the element shown in the figure. This bar is made of hot…

A:

Q: A rectangular post which is made up of two blocks of wood glued together along a joint inclined at…

A:

Q: ou A bar of steel has the minimum properties S,- 276 MPa, S,-413 MPa, and Sut 551 MPa. The bar is…

A:

Q: Q3 - The homogeneous bar AB have diameters 190mm when subjected to an axial tensile load of 34KN.…

A:

Q: ased on the yield stress rk out the allowable lo

A: A= 20x20= 400 mm2 Yield strength = 250 MPa F(s) = 4 Allowable stress = ? Working load =?

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: aw the free body diagram of the system shown below b.) Formulate the different equations of stress…

A: To determine the total elongation in the bar.

Q: The force P = 4 kN is applied to the steel (E = 200 GPa) rod AB of diameter d 50 mm. a) Determine…

A:

Q: A bar of 1000 mm length and 40 mm diameter is cen- trally bored for 300 mm length at one end at a…

A: