S The following data is given for th4e bracket illustrated P=25 kN, e 100 mm, 11-150 mm, 12-25 mm. There is no pre-load in the bolts. The bolts are made of plain carbon steel 45C8 (oy = 380 N/mm2) and the factor of safety is 2.5. Using the maximum shear stress theory, specify the size of the bolts. Į 12

S The following data is given for th4e bracket illustrated P=25 kN, e 100 mm, 11-150 mm, 12-25 mm. There is no pre-load in the bolts. The bolts are made of plain carbon steel 45C8 (oy = 380 N/mm2) and the factor of safety is 2.5. Using the maximum shear stress theory, specify the size of the bolts. Į 12

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7/8" Bolts t = 1/2" I Thickness Gusset plate Tension plate A36 Steel 3" 13" 3" P,= ? 3" Find the Tension Capacity of this plate, which is connected to the gusset plate with 16 -7/8" bolts 4" 4" Show A, of at least three most critical failure lines in your calculation
• The connection shown in the figure if the screw is type 9 8 and the two plates are A'SI 1040 CD steel, the highest tensile strength that can be shed longtunally so that the safety factor is nct less than 25 The following possiblities of failure E- Shearing the bolts b-Loading the bolts • Loading into the member. item I tensile in the element M24x3 40 sO 40 -100- 25
What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe figure if the ultimate shear stress in the 5-mmdiameter pin is 340 MPa?What is the maximum permissible value of theapplied load P to maintain a factor of safety of 3.0with respect to failure of the pin?
ded ! Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt = 60 kpsi and Syc = 75 kpsi. Using the ductile Coulomb-Mohr theory, determine the factor of safety for the states of plane stress. 0x = 16 kpsi, and Oy = -14.5 kpsi The factor of safety is 3.75
A -0.5 m- 400 KN B -0.5 m C 0.4 m D E F Figure 2 (not to scale) The assembly shown in Figure 2 consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1000 mm², and a 2014-T6 aluminium post BE having a cross-sectional area of 1500 mm². There is a small gap of 0.1 mm between the post BE and the rigid cap ABC. If a central load of 400 KN is applied to the rigid cap ABC, determine the normal stress in each post.
I need help with this question please. thank you
Required information A short cantilevered round peg made from AISI 1030 cold-drawn steel is 40 mm in diameter and extends 10 mm from the wall. It is loaded, as shown, with a force F= 50 kN applied at the tip in the negative z direction and a torque T=800 N-m. The cross section at the wall is also shown, with points of interest A, B, and C. 10 mm 92 The minimum factor of safety is 2.93 Cross section at the wall Evaluate the state of stress at points A, B, and C, determine the critical case, and evaluate the minimum factor of safety based on the distortion-energy theory.
Mechanical design
2) The pillow block shown in Figure 2 is attached to the fixed plate by using two M20x1.5 ISO class 5.8 bolts. The member stiffness per bolt is given as km=3.5kb. The connection is assumed to be permanent. Determine the factor of safety values guarding against yielding, over load and joint seperation. 9 kN Rotating shaft Pillow block Metric (ISO) screw Figure 2
Can someone slove the fx and fy equations in the below questions solution in steps to how we got f1 and f2 values. Thanks.
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20