The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to bearing stress. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material. N = 47,

Q: 14. A commonly used method of fastening one part to another part iscalled “shrink fi tting.” A steel…

A: Understand that the diameter of the rod must get reduced at least the hole diameter for the shrink…

Q: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25…

A: Given data, Width of the main plate, bm = 300 mm Thickness of the main plate, tm = 20 mm Thickness…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A: Given data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: The one end of a hollow square bar whose side is 10.35 in with 1.35 in thickness is under a tensile…

A:

Q: The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the…

A:

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

A:

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A:

Q: A) What is the axial force along AB? FAR = units B) What must be the minimum diameter of the pin at…

A: Given:P=200 lbFoS=2.5shear stress at failure for the pin material= 16 ksi

Q: P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

A: Given, σy-B = 60 MPaσy-CD = 100 MPaSF = 2t = 6 mm   Consider below FBD for the given question:

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. Figure 4 ft 3 f 1 of 1 >…

A:

Q: The one end of a hollow square bar whose side is (10+N/100) in with (1+N/100) in thickness is under…

A:

Q: Required Information The part shown is made from AISI 1030 CD steel and is loaded at point C with…

A: Given : material - AISI 1030 CD diameter of bar d = 12 mmNote : Yeild strength for AISI 1030 CD is…

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

A:

Q: The simplest truss consists of two rods and is loaded by a force. F Given: angle a=64°. Cross…

A: Find the largest force Given data:- Yield strength = 270 Mpa Factor of safety = 2.2

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: The information provided in the image includes:Maximum cylinder pressure: 3.15 N/mm²Cylinder bore:…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A:

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

A: Given Data:- Side(s)  =0.1m = 3.93inch.......considering the unit as meters  Thickness (t) =0.01m =…

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: The one end of a hollow square bar whose side is 0.1 with  0.01 thickness is under a tensile stress…

A:

Q: The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm…

A: As given question  Load =50 kn T=20mm n=3 Dia=18mm We have to find shear stress, bearing stress and…

Q: The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum…

A:

Q: The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a…

A:

Q: Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two…

A: Given Data The diameter of the shaft is: d=50 mm The yield strength of the shaft is: σy=440 MPa The…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A:

Q: Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts…

A:

Q: A long tensile member is constructed by connecting two plates as shown. Each plate is 2 in x 9 in,…

A:

Q: The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile…

A:

Q: The steel bar has the dimensions shown in Figure 2 below. Determine the maximum axial force P that…

A: To find: The maximum axial force P. Given: The ultimate normal stress is σu=215 MPa. The factor of…

Q: factor of safet

A: d= 40mmF = 29KNL = 796mmT = 1.7KNmfail stress = 156MPamaterial- brittle cast iron

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Given Data: The side of the hollow square bar is s =10.47 in. The thickness of the bar is t = 1.47…

Q: The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under…

A: Data given -  Side a = 10+ 47/100 = 10.47 in  Thickness t = 1+47/100 = 1.47 in  tensile stress σt =…

Q: The one end of a hollow square bar whose side is 10.69 in with 1.69 in thickness is under a tensile…

A:

Q: Question: 35 35 The one end of a hollow square bar whose side is (10 +) in with (1 +) in thickness…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.