P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

Q: The column AB is connected to the frame through pin-joints as shown in Figure 1. There exists a…

A: Given  G = 40 KN/m Q = (LL) = 20 KN/m   d=depth= 198 mm  bf = flang width = 99 mm  tf = flang…

Q: The aircraft link is made from an A992 steel rod (Eigure 1) Part A Determine the smallest diameter…

A: Buckling load,(PC)=6 kip The length of the link,(L)=18 in For A992 steel, (E)=29×103 ksi. Determine…

Q: mechanical design A steel cantilever is 200 mm long is made from AISI 4340 quenched and tempered at…

A: after using scientific calculator The diameter d of the cantilever is approximately 5.2 mm

Q: a. Two brass rods used as compression members, each of 3-m effective length with pin end, have the…

A: Given:Effective length of the rods, Le=3 mOuter diameter of circle, do=60mmInner diameter of circle,…

Q: ■ solid square rod is cantilevered at one end. T ansverse load at the other end of 50 kN. The r =…

A: Length L= 0.8 mLoad P= 50 KNSyt= 370 MPaSut= 680MPaDesign factor n= 2

Q: Link 2, shown in the figure, is 25 mm wide and 11 mm thick. It is made from low-carbon steel with…

A: Wide W = 25 mm Thickness t = 11 mm Sy = 165 MPaForce F = 80 KNFor  low-carbon steel E = 207GPa

Q: A 'L' shaped post with a cylindrical cross-section is loaded with a concentrated load at its free…

A: Given: To find: State of stress at P1

Q: the ground and free in the upper end. a) Calculate the compressive stress, then the minimum…

A: Given Data: H=3 mm=1000 kgFOS=3σut,c=241 MPaE=190 GPa   To Find: (a) The compressive stress. (b) The…

Q: 1. Determine the diameter size of rods AB, BC and C if ay = 3600 MPa and the safety factor SF= 2.…

A: Determine the diameter size of rods AB, BC and CA, if Yield stress = Sy = 3600 MPa and the safety…

Q: (13%) Problem 5: A shop sign weighing msg hangs from one end of a uniform beam weighing mpg. A hinge…

A:

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. Figure 4 ft 3 f 1 of 1 >…

A:

Q: The figure shows a connection that employs three SAE grade 4 bolts. The tensile shear load on the…

A: From Table 8-9: for SAE Grade 4 boltsFrom Table A-20: for AISI 1020 HR

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity  Loadbearing capacity is the maximum ability of a structural member or…

Q: Use LRFD and design a 13-foot-long tension member and its connection for a service dead load of 8…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: Determine the reactions at A and E if P = 500 N. What is the maximum value which P may have for…

A:

Q: Part A Determine the smallest diameter of the rod that will support the load ofP = 3.4 kip without…

A:

Q: A circular bar is used as a column carrying a load of 8500 lb with pinned ends The length of the bar…

A:

Q: factor of safet

A: d= 40mmF = 29KNL = 796mmT = 1.7KNmfail stress = 156MPamaterial- brittle cast iron

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.