Rod AB has a diameter d and fit snugly between the rigid supports at A and B when it is unloaded. The modulus of elasticity is E. Determine the support reaction at A and B if the rod is subjected to the linear distributed axial load. Po Pox B

Rod AB has a diameter d and fit snugly between the rigid supports at A and B when it is unloaded. The modulus of elasticity is E. Determine the support reaction at A and B if the rod is subjected to the linear distributed axial load. Po Pox B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rigid rod AB is attached to a hinge at 4 and to a spring with stiffness Eat D. The critical…

A: Rigid rod AB attached to spring at D

Q: number of significant digits; the tolerance is +_1 in the third significant digit

A: Step 1: At joint C, the forces are FCE,FCD and the external Load of 5.5kNSum of forces in y…

Q: The prismatic bar has a solid circular cross section with 2-in. radius. Determine the average normal…

A: Given data : Radius (r)=2

Q: Knowing that all = 24 ksi and Tall = 14 ksi, select the most economical wide flange shape that…

A: Allowable bending stress= 24 ksi allowable Shear stress= 14 ksi To find:- Most economical wide…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: 3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear…

Q: A solid 5/8-in. steel [E = 29,000 ksi] rod (1) supports beam AB, as shown in Figure. If the stress…

A: Given : steel dia = 5/8 in E = 29000 ksi Allowable stress in rod = 30 ksi max. allowable deformation…

Q: F₁70 kN and F2 = 60 kN. A is a pin, and F is a roller. Figure -2 m- 40 kN E 50 KN -2 m- H -2 m D C 1…

A: Given data- F1 = 70 KN F2 = 60 KN Find out - Force in member EH ?

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: Given data- Cross sectional area of Truss member = 3.6 in2 Maximum normal stress in each member = 50…

Q: The lap joint is connected by four rivets. Assuming that the axial load P = 30000 lb is distributed…

A: Given Shear stress of the rivets= 16 Ksi Bearing stress between rivet and plate = 22 Ksi Tensile…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross- sectional…

Question

Rod AB has a diameter d and fit snugly between
the rigid supports at A and B when it is unloaded.
The modulus of elasticity is E. Determine the
support reaction at A and B if the rod is subjected
to the linear distributed axial load.
Po
= Por
B
L-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z + 23e3. Assuming stress-strain relation: S = aE, where a is a constant, total force on the base of the cylinder with normal -e3 is f = -1.5anR2 He3 total force on the base of the cylinder with normal - ez is f = 1.5aπR²e3 total force on the base of the cylinder with normal - ez is f = 1.5an R²Hez total force on the base of the cylinder with normal - ez is f = -1.5anR²e3
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P
Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
,,
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1600 mm2. Assume a = 2.4 m, b = 9.1 m, and c = 3.5 m. If P = 40 kN and Q = 90 kN, determine the normal stress in each member.
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
If the maximum bending stress at section a–a is not allowed to exceed an allowable stress of 220 MPa, determine the maximum allowable force P that can be applied to the end E.
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1160 mm2. Assume a = 2.3 m, b = 6.8 m, and c = 2.8 m. If P = 50 kN and Q = 75 kN, determine the normal stress in each member. L. Answers: JAB OBC i i JAC= i P b MPa (C) MPa (T) MPa (T)