number of significant digits; the tolerance is +_1 in the third significant digit Determine the forces in members BE and CE of the loaded truss. The forces are positive if in tension, negative if in compression.3.3 m4.5 KN5.5 kN48°2.9 mE2.9 mBC=CDAnswers:BE=iKNCE=iKN

Step 1: At joint C, the forces are FCE,FCD and the external Load of 5.5kNSum of forces in y…

Answered: Determine the forces in members BE and…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
∆ = 0
The thin square plate shown is uniformly deformed such that €, = +1445 pE, E, = -674 uE, and y,y = +1260 urad. Determine the normal strain e, in the plate. 60 mm O -157 µE O -309 µE O -198 HE O -244 µE O -256 HE
The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top of this device). Assume that the wires are 0.05 inches diameter. If the skycam weighs 77 lbs, then the tensile stresses of wire 1 and wire 2 are Blank 1 ksi and Blank 2 ksi respectively. SN= 77
Problem 5 Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy [E = 10,000 ksi] bars attached at joints A and C. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2= 59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by A = 0.12 in. After bar (2) has been stretched and connected to the pin at C. Use the following additional properties and dimensions: A1 = A2 = 0.75 in², Determine: (a) the normal stresses in bars (1) and (2). (b) the deflection at A of the rigid bar. (1) 40 in 36 in Rigid bar 54 in P-20kips (2) L₂ 48 in D
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature. Brass L=2 m A= 1200 mm E= 100 GPa a = 18,7 x 10-y°C B -2 m Соpper L=3 m A = 1500 mm E= 120 GPa a = 16.8 x 10-bj°C FIG. P2.108
Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction. S11=7.6 (TPa)-', S12 = - 2.8 (TPa)-', S44 = 8.6 (TPa) -!
if a certain type of steel has a ultimate strength of 185 ksi, calculate the value of constant a(alpha) for the material. choices: a. 0.00438 b 0.000438 c. 0.000348 d. 0.0003438
Please solve this question and please mention the all the correct answer
Question 3: The block shown is made of a magnesium alloy for which E=760GPa and 9 =0.35. Knowing that o=157 MPa, determine (a) the magnitude of o, for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
A circular bar of magnesium alloy is 390 mm long. The stress-strain diagram for the material is shown in the figure. 70 63 56 49 O (MPa) 42 35 28 21 14 7 0.002 0.004 0.006 0.008 0.01 The bar is loaded in tension to an elongation of 2.34 mm, and then the load is removed. Hint: Use the concepts illustrated in the figures below. (Assume the curve in the figure above is linear between (0, 0) and (0.001, 28), and curves with a gradually decreasing slope otherwise.) F В E F Loading CD Loading Residual Elastic strain recovery (a) What is the permanent set of the bar (in mm)? 2.184 X mm (b) If the bar is reloaded, what is the proportional limit (in MPa)? 55 X MPa
The stress-strain relationship shown in Figure P1.13 was obtained during the tensile test of an aluminum alloy specimen. Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress of 310 MPa c. Yield stress using an offset of 0.002 strain d. If the yield stress in part c is considered failure stress, what is the maximum working stress to be applied to this material if a factor of safety of 1.5 is used? 450 300 150 0.002 0.004 0.006 0.008 Strain, m/m FIGURE P1.13 Stress, MPa

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Determine the forces in members BE and CE of the loaded truss. The forces are positive if in tension, negative if in compression. 3.3 m 4.5 KN 5.5 kN 48° 2.9 m E 2.9 m BC=CD Answers: BE= i KN CE= i KN