*n 2020-2021) section (1) e doft.com/.?culture en uskcountry-wwelm deeplinkPalmsrc-NeutralHomePageWeb&cmpid Wetignin#/shool/tatr3717002657/192First Quiz (strength of materials) (Strength of Materials (Spring 20-* Question(ähai 2)Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod(1), which has a circular cross section. If the normal stress in rod (1) must be limitedto 30 MPa, determine the minimum diameter required for the rod.(1)2000 mm1000 mmmm 40.82mm 36.18 Omm 50 Omm 56.42

Answered: Image /qna-images/answer/c3d2fabe-d321-48f2-b6a1-eae99491674b.jpg

Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1), which has a circular cross section. If the normal stress in rod (1) must be limited to 30 MPa, determine the minimum diameter required for the rod. (1) A C 2000 mm 1000 mm

Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1), which has a circular cross section. If the normal stress in rod (1) must be limited to 30 MPa, determine the minimum diameter required for the rod. (1) A C 2000 mm 1000 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 23 mm and the diameter of rod (2) is d2 = 34 mm. Determine the absolute value of the normal stress in rod (2). 80 KN d₁ 232 MPa 255 MPa 305 MPa O 160 MPa O 220 MPa 140 KN 140 KN B
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.2500 in. The average shear stress in the pin cannot exceed 35 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
The rectangular bar has a width of w = 3.00 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load Pis applied. Assume a = 3 and b = 4. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. A P b. B Answers: (а) Р- kips (b) Tnt = ksi (c) Omax ksi ksi Tmax =
The homogenous bar ABCD shown in the figure is supported by a cable that runs from A to B around the smooth peg at E, a vertical cable at C and a smooth inclined surface at D. Determine the mass of the heaviest bar that can be supported if these stress in each cable is limited to 95MP. The area of the cable AB is 350mm^2 and that of cable at Cis 270mm^2. AL C 2m 2m (50
Determine the uniform cross-section of the truss members BC, BE and AE, if the allowable stresses for all members is 150 psi for tension and 125 psi for compression. Given that applied force at point is P = 3.6 kips as shown. Neglect weight of truss members. Find the answer for A only. Answer: A = ___________________
A 2m long bar with square cross section of side 40 mm is subjected to compressive stress of 70 MPa along three mutually perpendicular directions. Take Young's modulus as 200 GPa and Poisson's ratio as 0.3 for the material. Determine change in volume. O a. 1.344 mm3 O b. 1.344 m³ O c. 1344 mm³ O d. 1344 m³
2. A replacement disc consists of the tube Cwith larger diameter of 4 cm, the cylindrical core B with the diameter of 2 cm and two relatively rigid discs on both ends. The disc replacement placed between vertebrae is under compressive force of 400N. The corresponding moduli of elasticity are Ec=10MPA and EB=20MPa. Determine the stress in the tube A and the core B. F Rigid parts 1cm C 2om 4cm F (Answer: OB = 509.3KPA, oc = 254.6KPA) 254.6KРа) %3D
Solve by hand please
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 345 MPa, determine the minimum diameter d2 required for rod (2). di 140 kN 80 kN 140 kN B 37.2 mm O 35.0 mm O 22.8 mm O 27.2 mm 25.2 mm
The rigid beam BCis supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm?. The cross- sectional area of rod (2) is 17 mm?. For a uniformly distributed load of w = 4.2 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L= 4.85 m. (1) (2) B |C
The W-kg man stands in the position shown. If the center of gravity of the man is at Gand assuming that the contact point at C is smooth.a) Find the reactions at B and C. b) Determine the state of stress at point A on the cross section of the plank at sectiona–a (Cubic stress element in 2D).
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 3.00 ft and b = 3.60 ft. If the normal stress in each member must not exceed 35 ksi, determine the maximum load Pmax that may be supported by the structure. A Answer: Pmax= b B b kips