Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1), which has a circular cross section. If the normal stress in rod (1) must be limited %3D to 110 MPa, determine the minimum diameter required for the rod.

Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1), which has a circular cross section. If the normal stress in rod (1) must be limited %3D to 110 MPa, determine the minimum diameter required for the rod.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.3125 in. The average shear stress in the pin cannot exceed 45 ksi, and the bearing stress in the pulley support bracket cannot exceed 65 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
* Your answer is incorrect. The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial distributed loading along its length of w= 9 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.5 m. Assume a = 0.7 m and b = 1.3 m. W B >x 45012 MPa a Answer: 0 = b
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 8 mm². The cross-sectional area of rod (2) is 17 mm². For a uniformly distributed load of w = 2.8 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.20 m. (1) B Answer: a = i L W E 2
The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load Pis applied. Assume a = 4 and b = 5. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. P B Answers: (а) Р- i kips (b) Tự = i ksi (c) Omax = i ksi Tmax i ksi
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
Two axial members are used to 4.3 m support a load P applied at joint B. Member (1) has a cross-sectional area of A: = 3,080 mm? and an allowable normal stress of 180 MPa. Member (2) has a cross-sectional area of A2 = 4,650 mm? and an (1) 5.0 m allowable normal stress of 75 MPa. Determine the maximum load P that may be supported by the structure without exceeding either allowable normal stress. (2) 2.0 m
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 590 mm, b = 295 mm, h = 360 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a ● b
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 12 mm. If the normal stress in rod (1) must not exceed 225 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Dot A Answer: W = ↓↓ a i 1 B W b (1) ↓↓ kN/m &
X Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 170 MPa, determine the minimum diameter d2 required for rod (2). d₂ d₁ 140 KN 80 KN 140 KN C A ↑ 45.5 mm 49.0 mm O 35.3 mm 38.7 mm O 53.8 mm B
Strength of materials
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 920 mm2. Assume a = 2.4 m, b = 9.0 m, and c = 4.1 m. If P = 60 kN and Q = 75 kN, determine the normal stress in each member. P y L₂ C MPa (C) Answers: OAB = a b