Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 650 mm, b= 325 mm, h = 525 mm, P = 800 N, and 0= 65°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B7 (c) Tpin A = a i i i B b h MPa MPa MPa

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 650 mm, b= 325 mm, h = 525 mm, P = 800 N, and 0= 65°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B7 (c) Tpin A = a i i i B b h MPa MPa MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

A: Given data - Diameter of rod = 5 mm Diameter of Pin = 8 mm P = 750 N Find out - 1) Normal stress in…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

A: dr =5 mm d = 8 mm P = 800 N = 65o

Q: Hi. PLEASE ANSWER IT ASAP FOR AN UPVOTE. I NEED IT ASAP. Thank you. >>>Strength of…

A: Data given:Modulus of elasticity of aluminium cable (EAL) = 70 GPaArea of aluminium cable = 25…

Q: The pipe ACDE is supported by ball-and-socket joints at A and E and by the wire DF. Determine the…

Q: Question #4 The frame is supported by a rocker at A and a pin connection at E. Determine the…

A: Reaction at A,E,C,B,D

Q: A B F C D 000 4₁ L₂ L3 Fishing line with a tensile strength of 50 lbs is used at B to fasten 2…

A: Tensile strength of fishing line (T) = 50 lbs Determine the maximum force F that can be supported.

Q: Problem 6: Determine the location ỹ of the centroid of the beam's cross-sectional area. Neglect the…

A: It is asked to find the centroid of given figure:

Q: D (1) h B a b

Q: The bell crank as shown in the fig. is in equilibrium, determine the shearing force in the pin at D.…

A: To find shear force at D

Q: 5.42 The wall bracket shown is pin-connected at points A, B, and C. Calculate the pin reactions at…

Q: Determine the magnitude of the pin force at A. Assume W-620 lb, a-4.6 ft, b- 3.1 ft.r-8 in. B b W…

A: The size of a force is measured by its magnitude. It's the sum of all the forces operating on a…

Q: In the assembly shown. the block has a weight W =200 lbs and the cord is attached to the pin at B.…

A: To find reaction at link AB

Q: The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C,…

A: Find the forces in the member using method of joints:Initially consider all the member forces are…

Question

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is
supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter.
Assume a = 650 mm, b = 325 mm, h= 525 mm, P = 800 N, and 0= 65°. Determine the following:
(a) the normal stress in rod (1)
(b) the shear stress in pin B
(c) the shear stress in pin A
D
Answers:
(a) Orod =
(b) Tpin B =
(c) Tpin A =
(1)
a
i
i
i
B
b
MPa
MPa
MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given question

VIEW

Step 2: Normal stress in rod (1)

VIEW

Step 3: Shear stress calculation

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
Problem 1 Classify each of the structures as statically determinate or indeterminate. If indeterminate, specify the degree of indeterminacy. pin rocker fixed 7 pin roller fixed fixed pin roller pin (d) (h) pin fixed Page fixed
Determine the tensions in cables AB, AC, and AD. B Answers: TAB= TAC = TAD = i i i 2.3 1.45 m 180 kg D 2.20 m 1.30 m 0.40 m N N N
Problem 8: Determine the location ỹ of the centroidal axis i – i of the beam's cross-sectional area. Neglect the size of the corner welds at A and B for the calculation. -150 mm 15 mm B 150 mm -15 mm 50 mm
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE