Determine the magnitude of the pin force at A.Assume W - 620 Ib, a- 4.6 ft, b-3.1 ft,r-8 in.CBWAnswer: A-Ib

The size of a force is measured by its magnitude. It's the sum of all the forces operating on a…

Answered: Determine the magnitude of the pin…

Engineering

Civil Engineering

Determine the magnitude of the pin force at A. Assume W-620 lb, a-4.6 ft, b- 3.1 ft.r-8 in. B b W Answer

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Related questions

Q: A plane frame is constructed by using a pin connection between segments ABC and CDE. The frame has…

A: Given frame:

Q: Determine the force in each member of the bridge truss shown. State whether each member is n tension…

A: Solution: Considering the diagram:

Q: A frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a…

Q: 6-53) A beam is constructed from four pieces of wood, glued together as shown. If the moment acting…

A: Moment = 450N.m y= 120 I= 2×15×240312+2200×20312+200×20×1102I=181.6267 mm4 σmax=MI×y=…

Q: Determine the forces in members DE, DI, and JI of the arched roof truss shown below. -46- 44 6- -6-…

A: Consider the figure. Here, T is tension and C is compression.

Q: d 9.09

Q: 2. Use the method of sections to determine the internal forces in members JI, DI, and DE. The…

A: To find the value of the force developed in the members JI, DI and DE, using method of sections.

Q: 490 mm 200 mm 640 N B 480 mm 160 mm 240 mm PROBLEM 4.152 The pipe ACDE is supported by…

A: The objective of this problem is to determine the tension in the wire DF when a load of 640 N is…

Q: Both sections are made of steel with E-200 GPa. The gap between the bottom of the metal bar and the…

A: Given data: Length of section AB, L1=300 mm Length of section BC, L2=300 mm Area of section AB,…

Q: A 200 lb weight is suspended as shown. Wires DE and BC (E,wire = 29,000 ksi) have a 0.05" diameter.…

A: W=200lb

Q: 14 P. 15 Use the diagram shown above. Given P. 10 16 12'-0" TYP. P. 11 17 • P1 P2 P3 = 300 #…

Q: The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C,…

A: Find the forces in the member using method of joints:Initially consider all the member forces are…

Q: Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform 1 rectangular…

A: Given : E = 29 X 106 psi Cross section = 1/4 X 1 in. Determine the largest load which can be…

Q: Given a force F applied on the handles of the device, determine the force developed on the rod at A.…

A: Given data: F=6 lb from figure, ∑C=03×F-2.5×FAcos20°=00.939×2.5×FA=182.34×FA=18FA=7.69 lb

Q: The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.75 in.…

Q: Determine the force in Pin C for the frame shown. Frame comprises three members - AC, AB, and BD.…

A: To determine the force in Pin C for the given frame, we need to analyze the static equilibrium of…

Concept explainers

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.

Question

Determine the magnitude of the pin force at A.
Assume W - 620 Ib, a- 4.6 ft, b-3.1 ft,r-8 in.
C
B
W
Answer: A-
Ib

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
Select an American Standard Channel shape for the following tensile loads: dead load = 54 kips, live load = 80 kips, and wind load = 75 kips. The connection will be with longitudinal welds. Use an estimated shear lag factor of U = 0.85. (In a practical design, once the member was selected and the connection designed, the value of U would be computed and the member design could be revised if necessary.) The length is 17.5 ft. Use Fy=50 ksi and Fu=65 ksi. a. Use LRFD. b. Use ASD.