The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.75 in. If a force of 10 kip is applied to the bar, determine the angle of tilt of the bar. (Refer to Figure 2)

Q: The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete…

A:

Q: w H1 0.5 L 0.5L Figure 3 Activ. 6.2 Span "L" in metre Height (H1) in metre Live Load on the slab…

A: Strain energy hypothesis proposes that disappointment will happen when the strain energy per unit…

Q: What is the shear wall?

A:

Q: Define what is Two-way shear ?

A: One way shear One way shear will be ruling in linear structures like beam, combined footing…

Q: Define scour

A: Scour is the removal by hydrodynamic forces of granular bed material in the vicinity of coastal…

Q: Define Excavation Bracing.

A: The excavation bracing can be defined as it is a support which is used transfers the lateral earth…

Q: Describe the Plumb bob technique in setting out and its uses? please describe in details.

A: A plumbob is used to check whether the objects are vertically placed or not. It consists of a weight…

Q: Define Caisson

A: Caisson: It is a hollow box or in the shape of a cylinder that is prefabricated which is sunk into…

Q: 4.2 Explain the difference between a "flat slab" and "flat plate" framing system. Draw a schematic…

A: Flat slab and flat plate

Q: Why hopper walls are steeply sloped ?

A: When hoppers square measure designed inconsiderately of the particular materials being handled,…

Q: Define metamorphic.

A: Metamorphic:

Q: Where

A: Required : To explain the number of cycle in 1 hour

Q: Which of the following is true about formwork? it tends to be labor intensive for elevated…

A:

Q: Draw with scale 1:10 a section in roof slab showing all layers used in roofing if you k

A: Solution- For the roof slab section - Scale = 1: 10 Slab thickness = 15cm Parapet height = 70cm

Q: Define Precast Concrete Slab.

A: Definition, Elaboration and Illustration below for Precast Concrete Slabs.

Q: Check for subsidence and reinforcement detail.

A:

Q: Q2/A: Draw with suitable scale the details of "T' junction clay brick bearing walls 240 mm and 360…

A: Solution:- The  suitable scale the details of 'T' junction clay brick bearing walls 240 mm and 360…

Q: What is the punching shear failure?

A: Punching shear failure: Punching shear is also called as two way shear. It is the shear that is…

Q: A & C are incorrect, please re-work

A: As per question , I solve here only a and c. Find out - (a) Radius of curve  (c) Tangent length

Q: What is work breakdown structure of single room of 5x5 m2?

A: When the work is broken down into smaller tasks in order to make the work more manageable and…

Q: What perameters are used for Existing ground level ?

A: Solution: Ground level means the existing level of the site at any of the point. When earth filling…

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: Define Decay of Timber

A: Timber decay is caused by a biological attack within the wood by bound species of fungi. The fungus…

Q: how to determine timber density

A: Given - To state the process to determine the density of timberTimber density can be determined by…

Q: Define one-way solid slab.

A: One way slab is supported on two opposite side thus structural action is only at one direction.…

Q: flowchart detailing the deisgn of One-way Slab

A: One-way Slab: - It is a slab in which longer span is equal or greater than 2 times of shorter span…

Q: A CPLD is based on

A: A CPLD- Complex Programmable logic device It is a programmable device based on complexity PALs and…

Q: What is grout?

A: Answer Grout- Grout is the process of injecting the paste of cement, sand, or other chemicals by…

Q: Draw to show the subgrade working area.

A: Subgrade soil -  The integral part of the road pavement which provides adequate support to the…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: GICR register?

A: GICR REGISTER:

Q: V5-4. For the 50-foot grid shown in Fig. 5-12, redraw, and sketch all one-foot contour lines. the…

A: Calculations of the distances of the points from the lower levels

Q: Q3/ List four points of the Engineering Properties for the Bricks?

A: Brick is one of the oldest materials used in engineering construction work. It mainly used in…

Q: Draw the structural details of the following sections (an elevation view and a side view)

A: Approach to solving the question: used autocad Detailed explanation: Examples: cad Key references:…

Q: Arch 486 Detail Problem: 2023 Detail Problem Draw a pinned connection and a fixed connection for…

A: Fixed Connection: For a 2 dimensional structure, fixed connection has three reaction forces. They…

Q: What is the Comparisons between the simplified Bishop and Fellenius methods?

A: The ordinary method or Fellenius method is regarded to be the easiest of slice methods because it is…

Q: What is the actual size of a 200 mm concrete block? Select one: O a. 190 mm O b. 210 mm O c. 150 mm…

A: To Determine :- Which one of the option given is correct.

Q: what is footing

A: Answer Introduction The important elements of the building which give stability to the structure are…

Q: Does waterproofing works comes after slab has been laid out or before?

A: Waterproofing is done in order to protect the structure from water intrusion and structure damage.…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.