Review the experiment and make sure you are familiar with the calculations. DO NOT INCLUDE UNITS IN YOUR ANSWER SUBMISSION. MAKE SURE TO FOLLOW THE INSTRUCTIONS FOR DECIMAL PLACES. Formula 3.33 points Use the data below to determine the Molarity of KMnO4 to THREE decimal places. (MM sodium oxalate 134 g/mol) mass of sodium oxalate (g) 0.094 initial buret reading (mL) 0.71 final buret reading (mL) 16.22 Type your answer... Next -Ɖ

Review the experiment and make sure you are familiar with the calculations. DO NOT INCLUDE UNITS IN YOUR ANSWER SUBMISSION. MAKE SURE TO FOLLOW THE INSTRUCTIONS FOR DECIMAL PLACES. Formula 3.33 points Use the data below to determine the Molarity of KMnO4 to THREE decimal places. (MM sodium oxalate 134 g/mol) mass of sodium oxalate (g) 0.094 initial buret reading (mL) 0.71 final buret reading (mL) 16.22 Type your answer... Next -Ɖ

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter4: Types Of Chemical Reactions And Solution Stoichiometry

Section: Chapter Questions

Problem 4RQ: Molarity is a conversion factor relating moles of solute in solution to the volume of the solution....

See similar textbooks

Similar questions

A throat spray is 1.40% by mass phenol, C6H5OH, in water. If the solution has a density of 0.9956 g/mL, calculate the molarity of the solution.
Molarity is a conversion factor relating moles of solute in solution to the volume of the solution. How does one use molarity as a conversion factor to convert from moles of solute to volume of solution, and from volume of solution to moles of solute present?
The units of parts per million (ppm) and parts per billion (ppb) are commonly used by environmental chemists. In general, 1 ppm means 1 part of solute for every 106 parts of solution. Mathematically, by mass: ppm=gsolutegsolution=mgsolutekgsolution In the case of very dilute aqueous solutions, a concentration of 1.0 ppm is equal to 1.0 g of solute per 1.0 mL, which equals 1.0 g solution. Parts per billion is defined in a similar fashion. Calculate the molarity of each of the following aqueous solutions. a. 5.0 ppb Hg in H2O b. 1.0 ppb CHCl3 in H2O c. 10.0 ppm As in H2O d. 0.10 ppm DDT (C14H9Cl5) in H2O
You wish to prepare 1 L of a 0.02-M potassium iodate solution. You require that the final concentration be within 1% of 0.02 M and that the concentration must be known accurately to the fourth decimal place. How would you prepare this solution? Specify the glassware you would use, the accuracy needed for the balance, and the ranges of acceptable masses of KIO3 that can be used.
Find the molarity of a 40.0% by mass aqueous solution of sulfuric acid, H2SO4, for which the density is 1.3057 g/mL.
What mass of HCl is contained in 45.0 mL of an aqueous HCl solution that has a density of 1.19 g cm-3 and contains 37.21% HCl by mass?
A solution is 0.1% by mass calcium chloride. Therefore, 100. g of the solution contains g of calcium chloride.
What volume of 0.0105-M HBr solution is required to titrate 125 mL of a 0.0100-M Ca(OH)2 solution? Ca(OH)2(aq)+2HBr(aq)CaBr2(aq)+2H2O(l)
What is the difference between a solute and a solvent?
A solution is formed by mixing 1 gal ethanol with 10 gal gasoline. Identify the solvent and the solute.
Polychlorinated biphenyls (PCBs) have been used extensively as dielectric materials in electrical transformers. Because PCBs have been shown to be potentially harmful, analysis for their presence in the environment has become very important. PCBs are manufactured according to the following generic reaction: C12H10+nCl2C12H10nCln.+nHCl This reaction results in a mixture of PCB products. The mixture is analyzed by decomposing the PCBs and then precipitating the resulting Cl asAgCl. a. Develop a general equation that relates the average value of n to the mass of a given mixture of PCBs and the mass of AgCl produced. b. A 0.1947-g sample of a commercial PCB yielded 0.4791 g of AgCl. What is the average value of n for this sample?