Required information Problem 04.120 - Horizontal platform - DEPENDENT MULTI-PART PROBLEM-ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part The total load acting at the center of a horizontal platform ABCD is 450 lb. The platform is normally held in position by hinges at A and Band by braces CE and DE Assume that the hinge at Bhas been removed. Also assume that the hinge at A can exert an axial thrust, as well as couples about axes parallel to x- and y-axes. Consider brace DE removed. 4 ft B D Problem 04.120.b - Reactions from supports Determine the reactions at the hinge and the force exerted by the remaining brace CE. lb. The force exerted by the brace CEis The reaction at A is (lb)i lb)] ( lb) k.

Required information Problem 04.120 - Horizontal platform - DEPENDENT MULTI-PART PROBLEM-ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part The total load acting at the center of a horizontal platform ABCD is 450 lb. The platform is normally held in position by hinges at A and Band by braces CE and DE Assume that the hinge at Bhas been removed. Also assume that the hinge at A can exert an axial thrust, as well as couples about axes parallel to x- and y-axes. Consider brace DE removed. 4 ft B D Problem 04.120.b - Reactions from supports Determine the reactions at the hinge and the force exerted by the remaining brace CE. lb. The force exerted by the brace CEis The reaction at A is (lb)i lb)] ( lb) k.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It's urgent please solve asap.
15° An actuator applies a force to a cable to hold the blade in place while the table holding the CheezeT drops away. The cable is redirected over a stationary drum. Determine the maximum load on the actuator and choose a material for the drum (explain your choice). (25 points) Concrete: us=0.5 Teflon: us=0.1 Cheeze Table
It's mechanical engineering subject. Calculate reaction forces at supports.
Draw a complete and correct free-body diagram of each of the body designated in the statement. The weight of the body is significant only if the mass is stated. All forces, known and unknown, should be labeled.
Parvinbhai
Question 2 A rigid box with built-in lifting lugs is to be lifted as shown. Given that the: Included angle between the diagonally opposite sling legs is 60 degrees. Chain slings are Grade 80 chain. Chain diameter is 13mm Calculate the maximum load that can be lifted and provide final answer in kilograms Show all calculations
(a) The free body diagram of the rudder. (b) If the maximum permissible load that the steel operational cable can handle is 3kN, determine whether it can handle the load of the rudder or not. (c) Determine the resultant load on the fixed pivot (A) and the angle at which it acts. (d) If the thickness of the rudder is included, describe which method you would use to find the centre of gravity? How would this value differ from the calculation using a lamina modelling assumption?
Consider the truss shown in (Figure 1). Figure 1.5 m E -2 m 3 kN D B -2 m 1 of 1 Part A Identify the zero-force members in the truss. Check all that apply. OBD OBE ооооооо CD O AB ODE O AE D BC Submit Provide Feedback Request Answer
A Assignment 7 A Assignment 6 google.com/c/MZA1MJAXMJY3MZM5/a/MZCXNJKYMDM20TE0/details Question 1: The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. Determine, using the method of joints, the force in members (BA), (BE), and (DE) of the truss and indicate if these members are in tension (T) or compression (C). Set P1 = P2 = 4 kN. 30° 30° E 3 m 3 m 321 EN O
A bus shelter consists of a frame supported by a pin at A and cable DF. There are also pins at B, C, D and E. Note the snow load on top of the shelter. Assuming weightless members, determine the magnitudes of the reactions at pins A, B and C, as well as the tension Tin the rope DF. Make sure you show the magnitude and position of the equivalent point load in a FBD. Provide Given, Find, Assumptions, Problem Type/Features, FBDS, Calculations, and Conclusions in your solution. 5. kg/m 2 m 1 m 1m 3 m В 2 m A F 3 m
Translate question. 1. Calculate all the forces acting on each bar from the truss below. 2. Known a bar that receives a load and is supported simply at the end as shown below.Asked: draw a force diagram along the stem
SOVLE FOR THE REACTIONS AT THE HINGE AND ROLLER SUPPORT. NEED COMPLETE SOLUTION IN 10 MINS. PLEASE, ASAP. THANK YOU.