Bar, initially horizontal but deflected under load L. Pinned to rigid support at each end. B

Q: An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The…

A:

Q: The y-component of the force F which a person exerts on the handle of the box wrench is known to be…

A: The angles from given figure are - cosθ=513,  sinθ=1213 The y-component of force is given by-…

Q: 1. The y component of the force F which a person exerts on the handle of the box wrench is known to…

A:

Q: The cable shown in Fig. weighs 35 N/m. Determine the maximum tension in the cable and the sag ha in…

A: Draw the free-body diagram of the cable.

Q: Determine the forces acting on the elements "CD", "DE" and "CE" of the space armor shown in the…

A: In the given truss, at joint A one force is known and 3 forces are unknown.  So by applying static…

Q: An object is being held off the ground by a crane on the right and 4 constructions with a rope on…

A:

Q: The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown…

A:

Q: What is the magnitude of the force that box A exerts on box B?

A: Given data: The mass of block A is, mA=22 kg. The mass of block B is, mB=8 kg. The horizontal force…

Q: If the plunger cylinder is with of area 12.5 m2 which lifts the other end of ram cylinder which is…

A:

Q: (a) Determine the x & y components of the force shown.

A: Force F = 106 lb

Q: A wooden plank with a mass of 50.968 kg is supported by two cables at its ends. At what location…

A:

Q: Q1: Determine the magnitude of the force on the pin at A for the boom shown in Fig. 1. Neglect the…

A:

Q: F lb В 60° 900 lb Q8: Assume that the components of the force of F are Fig. of (Q6, Q7 & Q8) equaled…

A: In vertical direction        FY sinθ=900×sin60=779.422 lb     -1

Q: the indicated location of the center of gravity of the 3100-lb pick truck is for the unlanden…

A:

Q: A beam 3m long has a weight of 200N at one end and another weight of 80N at the other end. The…

A: To solve this problem, we can set up the appropriate force system and then use the principle of…

Q: Q Choose and fill the blanks with the correct answer 1. The unit uscd to measure the force is -- (a.…

A: ● Force is an effect due to which objects comes in motion and it is measured in Newton ● Moment is…

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Given: There are four balls of equal radius and they are arranged in the form of tetrahedron. Weight…

Q: Using the Method of Components, find the resultant of the concurrent force system shown below. The…

A:

Q: 3. The arm of the excavator can be approximated with weights W1 and W2 located at their indicated…

A:

Q: The homogeneous bar AB weighs 111.2 N. Determine the magnitudes of the forces acting on the bar at A…

A: At hinge point A, two reactions produce; horizontal (RAH) and vertical (RAV) At point B, only…

Q: Please submit your assignment, which should include Drawing of the resultant force R, using the…

A: let consider two forces F1→ , F→2  and θ is the angle between them.let  F→1 passing trough x axis as…

Q: A weight, W hangs from massless ring A that is in equilibrium as shown. a. Draw Free Body Diagram…

A:

Q: For this question, imagine you are hanging a basket with the red cables shown below. Note that all…

A: Draw the top view and side view of given geometry As per the given condition, the red cables are…

Q: A 6.00-kg horizontal beam support- he beam and is supported at the corners the cable and the (b)…

A: given:mass of bar beam=6kgmass of sign =12kgθ=25

Q: Solve the hydrostatic force components of AB, BC, and CD using the general solution. Be sure to…

A: Given: The height of CD, h1 = 1 m The height of AB, 2.5 m

Q: The uniform crate shown below weighs 200lb. It is pulled up the incline by a counterweight W of…

A: Assume this diagram and the FBD,

Q: Question 2 (Type B): A triangular thin plate is supported by a ball-and-socket joint at A and a…

A:

Q: In Fig. the weight w is 60.0 N. (a) What is the tensionin the diagonal string? (b) Find the…

A: The free body diagram of the system at the lower joint end is as follows:

Q: 4.85 Determine the contact force between the smooth 100-kg ball B and the horizontal bar, and the…

A:

Q: Determine the direction the force was applied by the fireman on the fire hydrant nozzle while using…

A: When fluid flowing through the pipe a backward momentum of a fire hose is applied on the nozzle…

Q: The homogeneous triangular plate has a mass of 12 kg. Plot the DCL of the plate for each set of…

A: mass of plate = 9.81×12 = 117.72 N No. of unknown = 3

Q: The rigid body will remain in equilibrium when.

A: Let multiple forces area applied on a body. If the body is in rest condition or the body is moving…

Q: QB2: Determine the force in members GH, GB, and BC, and state whether each of these three members is…

A:

Q: The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown…

A: Given Data The angle of the crane is: θ=32° The distance a is:a=7 in The distance b is: b=34 in The…

Q: 1. Draw the Free Body Diagrams of pulleys A, B and C and then using these FBD calculate the force F…

A:

Q: The machine shown is used for moving heavy items such as pallets of bricks around construction…

A:

Q: A 150-lb cylinder is supported by two cables AC and BC that are attached to the top of vertical…

A: The free body diagram is shown below, The coordinate of point A is given as, A=-10.8,15,0 The…

Q: force exerted c

A: F=5150.3N

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.