Reinforcement Concrete Design solve the problem using NSCP 2015 4.Design lintel beam shown in Figure below. In your solution, assume that the beam supports in addition to its own weight all brick works that lie directly on it and supports a dead load of 12 kN/m and live load of 8 kN/m transferred from supported slab. Seats of the lintel beam can be simulated as simple supports in your design. Concrete Slab fc= 30Mpa, fy = 415 Mpa, assume main bar = 20 mm, stirrups = 10 mm, wt of bricks = 19 kpa Concrete Slab 6.00 m 1.43 m 0.50 m 0.30 m Ln = 6.3 m Lintel Beam Window 0.30 m 1.43 m 0.50 m -0.25 m Lintel Beam Window

Reinforcement Concrete Design solve the problem using NSCP 2015 4.Design lintel beam shown in Figure below. In your solution, assume that the beam supports in addition to its own weight all brick works that lie directly on it and supports a dead load of 12 kN/m and live load of 8 kN/m transferred from supported slab. Seats of the lintel beam can be simulated as simple supports in your design. Concrete Slab fc= 30Mpa, fy = 415 Mpa, assume main bar = 20 mm, stirrups = 10 mm, wt of bricks = 19 kpa Concrete Slab 6.00 m 1.43 m 0.50 m 0.30 m Ln = 6.3 m Lintel Beam Window 0.30 m 1.43 m 0.50 m -0.25 m Lintel Beam Window

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 300 mm Over-all depth, h = 425 mm Tension reinforcements = 5 pcs 28 mm dia Comp reinforcements = 4 pcs 20 mm dia Specified strength of concrete, f'c = 28 Мра Steel yield strength, fy = 345 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf
A concrete specimen with b = d is supported at both ends 600mm apart. It is tested for flexure strength with load at midspan of 100kN and failed with a flexural stress of 52.083 MPa. What is the dimension b and d of the specimen in mm?
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015