rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 377kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.25m from the support if the length of the beam is 2.57m. Note that the dead load includes the weight of the beam.

rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The nominal moment capacity multiplied by its strength reduction factor is 377kN.m. Determine the allowable concentrated live load in kN that it could carry acting at 2.25m from the support if the length of the beam is 2.57m. Note that the dead load includes the weight of the beam.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

A rectangular beam has a width of 269mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The depth of the concrete stress block is ___.
A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
an exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for tension which is laid out according to the code requirements. the depth of the tension strain of the beam is 353 mm. of the steel has a yield strength of 414 mpa. determine the following: Compressive strength of the concrete Maximum steel ratio Ultimate moment capacity of the beam
A concrete beam of length 5.5m is built monolithically with the slab. Originally, the beam has a width of 300mm and effective depth of 400mm. If the flange of the slab is 150mm and the total area tension steel bars is 500 sq.cm., determine the design capacity of the beam structure. The concrete has a compressive strength of 25 MPa, steels' yield strength is 420 MPa. and the beam's clear span from its adjacent beams is 2.15m.
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
A rectangular beam has a width of 283mm and an effective depth of 461mm. It is reinforced with 4-25mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The ultimate moment capacity is ___kN.m.
Please help:)
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
The T-beam shown in figure resulted from monolithic construction of the beam and slab. The effective flange width is 1100 mm and the uniform slab thickness is 120mm. Width of beam is 340 mm, total depth of the T-section is 590 mm. The centroid of steel is 70 mm from extreme concrete fiber. Concrete strength f’c= 21 MPa amd steel strength fy= 415 MPa. 1 Calculate the nominal strength of the beam for positive moment neglecting the contribution of the top reinforcement, KN-m A 428.55 B 503.20 C 355.96 D 637.52 2 Calculate the nominal strength of the beam for negative moment, KN-m A 289.88 B 275.53 C 311.67 D 325.48
In the reinforced beam having a width of 300mm and an effective depth of 600 mm, caries a moment of 80 KN - m which developed a max. stress of 5 MPa in the concrete. Determine the area of steel reinforcement required if n = 9, What stress is developed in the steel? d-600 b=300 As 200 400 300 nAs 100
determine the maximum concrete and steel stresses at the point of maximum positive and negative moment