R₂(1/2 w) w E3640A Power Supply V₂ R₁(1/4 w) Figure 2 Circuit to Determine Load Regulation In the circuit of Figure 2 with the source Vs = 15 V, Rs = 330 ohms, determine the minimum value of R₁ which can be used in the circuit without exceeding its 1/4 W rating or the current available. Then select a standard 10% value just larger than the calculated value. Again assume Iz > 3 mA.

R₂(1/2 w) w E3640A Power Supply V₂ R₁(1/4 w) Figure 2 Circuit to Determine Load Regulation In the circuit of Figure 2 with the source Vs = 15 V, Rs = 330 ohms, determine the minimum value of R₁ which can be used in the circuit without exceeding its 1/4 W rating or the current available. Then select a standard 10% value just larger than the calculated value. Again assume Iz > 3 mA.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

A circuit has resistance of 20 ohms and a reactance of 30 ohms. What is the power factor of the circuit? a. 0 b. 0.55 c. 0.832 d. 0.99
Find P5 and P100
Consider a typical electrical circuit system shown in Figure 2. The circuit consisting of two resisters value R, and R2 (ohm), a capacitance of value C (farad) and an inductance of value L (henry). The input is the supplied voltage V, and the output voltage is Vo- viz R1 Vi R2 Vo Figure 2 (1). Apply Kirchhoffs voltage law or other principles to derive the input-output dynamic model equation. (i). Apply Laplace Transform to determine the model transfer function for the electrical system. (i). Estimate the transfer function for the following R; = (ohm) and R2 = (ohm), L = (henry), and C = (farad) values. Task 4 R, (ohm) R: (ohm) C (farad) (henry) Note: Refer the Table for R1, R2, C and L values. 27 13 24 4 lellll
lo R1 CR2 V alx ........ Figure Q2(b) : Two Closed Loops Circuit (i) Explain the steps required in supermesh analysis for Figure Q2(b). (ii) Determine the mesh currents using the Kirchhoff's Current Law (KCL) and Kirchhoff's Voltage Law (KVL) for Figure Q2(b).
A PMMC instrument has a three-resistor Ayrton shunt connected across it to make an ammeter as in Figure 2. The resistance values are R1 = 4.52, R2=0.452 and R3= 0.052. The meter has Rm = 1k2 and Ifs.d = 50µA. Calculate the three ranges of the ammeter. [10.05mA, 100.05mA, 1.005A] Rm=1k2 B R3 R R, Selector Figure 2 수
Suppose the three branch currents in this circuit are I₁ = -3 A, I₂ = -18 A, and I3 = -15 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. V₂ B A B A C D 1₁ A B 1₂ 1₂ + Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -9 V -2 V C 9 V -11 V D
Please try to answer in typing format please ASAP for the I will like it please ASAP for Please answer all subpart either way
....hdhddd...
3.- For the following circuit, determine the following:(a) Currents in each branch. b) Potential differences between each branch (from junction to junction). c) Electric potentials in each junction with respect to ground
Q2.The periodic triangular current in shown in Figure 1 has a peak value of 180 mA. Find the average power that this current delivers to a resistor. etc. -Ty2 -T/4 T/4 T2 3T/4 /T -I Figure 1
Hi, I need a correct answer for this assignment question Thanks
Using superstition, find the value of i0 if voltage source at the left is 10, angle - 30 degrees V, and current source is 2, angle zero degrees. A total of three sources will be considered, separately. The 24 volt source is DC. When this source is acting alone, the capacitor will be open-circuited.