Find moment and maximum normal stress due to bending. (E=10^7 psi) r=0.3 in.MM0.05 in.0.005 in.cross section

Moment = 3.47 lb inMax Stress = 83.3 ksiExplanation:

Answered: r=0.3 in. M M 0.05 in. 0.005 in. cross…

Engineering

Mechanical Engineering

r=0.3 in. M M 0.05 in. 0.005 in. cross section

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be the value of X such that line YWZ is horizontal? Dimension in mm = 293
02/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm?. 490mm 125mm 30. 40 KN 125mm .-6 125mm 88mm 0-0-0-0
2) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN BAR CD SHOWN BELOW IN Fig 1.2 D -600lb -800lb B 4 7' 4' H. G 8' 8' Fig 1.2
Finding the cross sectional area Stress 22.66 N/mm2 Force=2 N
D= 1.75 in d= 0.75 in r= .120 in
16cm. 34.8cm = 1.0 SGcone = 0.9 Which is the more stable pesiton? IS
A left hand threaded 14 mm diameter A36 steel bolt is stuck in a metal block. Assume the bolt head is flush with the block surface at A. In order to remove the bolt the 50 Nm torque is applied to the bolt head as shown. The block applies a resisting torque "t" to the stuck threads which is assumed to be uniformly distributed along the 50 mm buried depth. G = 75 GPa a) Explain the difference between right and left hand threaded bolts Determine: b) The magnitude of the uniform resisting torque "t" (including proper units) c) The internal torque as a function of x measured from B (a FBD is required) d) The maximum shear stress in the bolt Ans: 92.8 MPa e) The angle of twist of bolt head A with respect to end B Ans: 0.0044 rad f) The largest torque that can be applied to the bolt head before it twists off (Tyield = 150 MPa) %3D
The stress-strain diagram for a polyester resin is given in Figure 2. The rigid beam AC is supported by a strut AB and post CD, where both are made from this resin material. a) When beam AC is subjected to a load of P = 80 kN, determine the angle of tilt of the beam when the load is applied. Assume that the diameter of the strut is 40 mm and the diameter of the post is 80 mm. b) Determine the largest load P that can be applied to the beam before it ruptures. Assume that the diameter of the strut is 12 mm and the diameter of the post is 40 mm. c) Based on the value of P in (b), suggest one material that will not rupture if the applied load is 5P. Explain your answer mathematically.
An L-shaped section has the following dimensions: The length of the longer leg is 5 in, the length of the shorter leg is 31/2., and the thickness of each leg is 3/8 in. The distance y from the back of the shorter leg to the neutral axis XX is A. 1.76 in B. 1.98 in C.1.53 in D. 1.61 in
I will be selling a Summer Camp Innovative Sleeping System (SCISS) that suspends beds from the ceiling to make cleaning the floor easier (and to avoid snakes, bugs, and rodents). The top post is a 4-foot long steel post with a 2.5 inch x 2.5 inch cross section. The bottom post is a 3-foot long aluminum post with a 2 inch x 2 inch cross section. (a) What is the displacement of point “C" for the loading shown? (b) Has the yield stress of either post been exceeded? (c) What is the displacement of point “C” if the 120 lb loads are put on the top beds, and the 180 lb loads are put on the bottom beds? (d) For the loading in part (c), has the yield stress of either post been exceeded? 180 lb 120 lb -A- Steel Aluminum O 180 lb 120 lb
Q.3) Determine Ixx and lyy for the composite section shown below. 50 mm 25 mm 30 mm 25 mm 50 mm 50 mm
Solidworks