For the following figure, calculate the shear stress, V, when x = 12.0 m. Draw the Shear Force and Bending Moment diagrams. Remember to correctly place the positive or negative sign and highlight the value of the absolute maximum shear force, th

For the following figure, calculate the shear stress, V, when x = 12.0 m. Draw the Shear Force and Bending Moment diagrams. Remember to correctly place the positive or negative sign and highlight the value of the absolute maximum shear force, th

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 2 shows a built-up cross-section of a horizontal beam which has a maximum shear force of 100 KN. Calculate the shear stresses and plot the shear stress distribution (Approximate the shear stress at the Neutral axis).
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. Let a=4.00 m, b=5.25 m, c= 2.50 m, P = 26kN and M = 160kN-m. Construct the shear-force and bending-moment diagrams. Use the bending-moment diagram to determine the maximum positive bending moment, Mmax, pos, and the maximum negative bending moment, Mmax, neg.
Determine the normal force, shear force, and moment about point C.
Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the appropriate reduced shear stress equation. Assume Vmax = 12kN. Find the max shear stress in a W12x50 cross-section using the appropriate estimated shear stress equation. Assume Vmax = 236kips. Find the max shear stress in bending in the cross section below if Vmax = 10 kips. 10" Flange 2" Web 2" 8" Flange 2" 10" • Identify where in the cross section the max shear will occur. • Determine the thickness of the cross-section at the location you wish to find shear stress. • Calculate the Ix for the shape (assume bending in the x with most basic beams). • Calculate Q by dividing the section into two pieces at the point you want shear stress. Select one of the pieces (either will work), I picked the top piece. • Use the Shear Stress equation to determine the requested stress. • Compare you answer: Max shear stress = at the center of the cross section.
Given the beam and the external loading shown below, if L = 15 m, w1 = 510 N/m and w2 = 1,600 N/m, calculate: • the magnitude and location of the equivalent resultant force (a single equivalent force, for the whole loading block, NOT two equivalent forces from dividing into rectangular and triangular stress blocks). • the reactions at the beam supports. W2 w, A L Resultant force Fr = 单位 (tolerance 1 N, magnitude only) Location xbar = 单位 (tolerance 0.1 m, measured from A) Reactions: Ay = 数字单位 (tolerance 1 N, observe up positive sign convention) MA= 数字单位 (tolerance 10 N*m, observe anti-clockwise positive sign convention)
Given the beam shown below, determine the shear force and bending moment at point C. Given the dimensions a = 2 m, b = 5.9 m and c = 2 m, and the load intensities e = 10 kN/m and f = 2 kN/m. e kN/m f kN/m am bm cm A B D Shear force (observe the up on the left, down on the right positive sign convention): SFc = Number Units (tolerance 0.2 kN) Bending moment (observe the sagging positive sign convention): BMc = Number Units (tolerance 1 kN*m)
2. The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m force along the section DE, a 50 N point force at point C, and a 200 N·m couple moment. a. Write the shear-force and bending-moment equations as a function of distance, x, measured from the leftmost point, A, for the entire beam. b. Using your shear-force and bending-moment equations, calculate the shear force and bending moment at x = 2 m and x = = 5 m. 200 N·m 50 N 40 N/m 1.m C D 2.5 m 1m 2.5 m E B 2 m
HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm respectively and pivoted on the axis of rotation. The mass of the central load is 17 kg, the mass of each ball is 3 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 27 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 35° and 45°, find, taking friction into account, the range of speed of the governor and Sensitiveness of Governors.
consider a beam with two 60-inch-long rods. The rods have a cross section area of 0.50 in 2 . Find the axial stress in each rod, draw the shear and moment diagrams for the beam, and find the maximum stress in the beam.
Draw a FBD of section CD. Do not solve the rest of the problem
Determine the axial force, shear force, and bending moment at point J located on member AB of the landing gear of an airplane, as shown in the figure.All distances are in inches.
Determine the normal force, shear force, and moment at point C. Take that P = 8 kN and M = 33 kN m. (Figure 1) Figure M B . 1 of 1 -1.5 m 1.5 m 1.5 m-1.5 m-