Determine the shear force (in kN) and bending moment M (in kN · m) just right of the 4.5 kN load on the simple beam AB shown in the figure. (Use the deformation sign convention.)4.5 kN1.8 kN/mCB0.5 m-1.0 m→-1.0 m→--2.0 m.4.0 m-V =kNM =kN • m

Answered: Image /qna-images/answer/2bc6154f-505a-49a0-a34a-8fccd399c550.jpg

Answered: Determine the shear force V (in kN) and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer ONLY HANDWRITTEN
I am struggling with this question
The cross-sectional dimensions of the beam shown in the figure are r = 113 mm and r;= 87 mm. Given M₂ = 16 kN-m, a = 37º, and ß = 53º, what are the bending stresses at points Hand K? H To a Part 1 Incorrect. Find the moment of inertia for a solid circular cross-section of radius 113 mm, then subtract the moment of inertia for a solid circular cross-section of radius 87 mm. Find the area moment of inertia for the cross-section about the z axis. Į₂ = mmª 7
Figure Q2 shows the cross section of a beam. The beam is simply supported over a span of 6 m and carries a vertical point load of 40 kN acting at its mid-span. Calculate The position of the horizontal centroidal axis of the cross-section from its bottom. The second moment area of the cross-section about the horizontal centroidal axis The maximum shear load per unit length (metre) at the lower surface of the top flange
For the beam shown in the figure, Calculate the support reaction forces and find the internal forces and moments at a point located 2 m from the right support and then draw the shear and moment diagram for this beam.
Draw the shear force and bending moment diagrams for the beam with loading shown below, P= 16 kN, w= 30 kN/m, M=40 kN.m. Also, state the maxmium shear force and bending moment in the text box. (Upload the diagrams showing all key values with units as well as neat and clear calculations) P kN P kN w kN/m M KN.m A 0.5 m 1 m 1 m- 1 m- -1 m
Determine the axial force, shear force, and bending moment at point J located on member AB of the landing gear of an airplane, as shown in the figure.All distances are in inches.
Q2 The internal bending moment in a beam with a cross sectional area shown in the figure is 500a in the direction shown. Nom Find: a) The centroid of the cross sectional area and, b) the maximum tensile and compressive normal stresses. Make a sketch showing the stress distribution A A -35 mm C2 100 mm C1 = ỹ 5 G0 Na m 25 mm B 50 25 50. mm 'mr mm
The cross-sectional dimensions of a beam are shown in the figure. Assume a = 45 mm, b = 75 mm, t = 4 mm and d =55 mm. (a) If the bending stress at point Kis 54 MPa (C), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress at point H. The bending stress is positive if in tension and negative if in compression. IT H Answers: (a) M₂= (b) og = i 945.9 144.881 d N-m MPa
In the following figure, there are two equal couples with a magnitude of M = 15 kNm. They act in opposite directions while being applied to the channel beam AB. These couples cause the beam to bend in the horizontal plane. Find: 1) Stress at point C 2) Stress at point D 3) Stress at point E
The simply supported beam in Figure below has a rectangular cross section 120 mm wide and 200 mm high: 1. Draw shear force and bending moment diagrams. 2. Compute the maximum bending stress in the beam. 10-kN/m 50m 25 m 100-m
Explain clearly and in detail

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the shear force V (in kN) and bending moment M (in kN • m) just right of the 4.5 kN load on the simple beam AB shown in the figure. (Use the deformation sign convention 4.5 kN 1.8 kN/m 0.5 m +1.0 m--1.0 m- - 2.0 m 4.0 m- V = kN M%3= kN m