Problem 2 ● 0.2m 100N 100Nm 0.3m 200N 100HM 0-2m - 10,000 N Calculate the axial stress, torsional stress, bending stress and the transverse shear stress at the most critical point in the cylindrical beam. The diameter of the beam is 14mm. You must explain why you chose the said point to be the most critical.

Problem 2 ● 0.2m 100N 100Nm 0.3m 200N 100HM 0-2m - 10,000 N Calculate the axial stress, torsional stress, bending stress and the transverse shear stress at the most critical point in the cylindrical beam. The diameter of the beam is 14mm. You must explain why you chose the said point to be the most critical.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A round beam of length 14-in is simply supported at A and D. The beam is loaded in torsion and with transverse loads. The diameter of the beam is 1.5in. Calculate the principal stresses and the max shear stress at the mostcritical point in the beam. solve from tan theta = 4/3 then theta =tan inverse(4/3) = 53.13 degree solve from theta for other force of 600 lb is theta = 45 degrees Then solve for each reactions, bending moment My, bending moment Mz and the maximum bending moment and maximum stress along x axis. And also calucalate the principle stresses and the maximum shear stress at the most crictical point in the beam. Show everything with proper digaram with step by step solution and give me right answer. And I will surely upvote for you and subscribe it.
AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 2 m, LBC= 5 m, LcD = 1 m, PA = 12 kN, WBC = 12 kN/m. Consider the entire 8-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. A PA LAB Answers: (a) OT = (b) oc = B i 62.19 i 25.81 WBC LBC 1 WT305 x 41 C LCD 88.9 mm 211.1 mm MPa. MPa. D x
For the following figure, calculate the shear stress, V, when x = 12.0 m. Draw the Shear Force and Bending Moment diagrams. Remember to correctly place the positive or negative sign and highlight the value of the absolute maximum shear force, the maximum positive and negative bending moments.
A single-piece bicycle crank is shown below under the following load: the rider pedals forward with a vertical force Fp = 500 N on the left pedal and no force on the right pedal. The chain exerts a force Fc on the chainring. The spindle is a solid cylinder with a diameter d = 16 mm. 1. Find the maximum normal stress and shear stress at cross-section y-y in image. Indicate the locations on the given cross section view where they act.
Find the max shear stress in bending in the cross section below if Vmax = 10 kips. 10" Flange 2" Web 2" 8" Flange 2" 10" • Identify where in the cross section the max shear will occur. Determine the thickness of the cross-section at the location you wish to find shear stress. • Calculate the Ix for the shape (assume bending in the x with most basic beams). • Calculate Q by dividing the section into two pieces at the point you want shear stress. Select one of the pieces (either will work), I picked the top piece. Use the Shear Stress equation to determine the requested stress. Compare you answer: Max shear stress = at the center of the cross section.
Draw the shear force and bending moment diagrams for 2 kip the beam under the external loadings shown in the figure. 200 lb/t Note use the graphical method; show all the critical tuming points of each curve, along with the calculation steps used in determining the critical points. 9
18
If the shear force is 50 kN, calculate the shear load per metre length at the top of the flangeof the T-section. [Start your calculations by setting the origin on the bottom of the cross- section].
The beam in (Figure 1) is made from three boards nailed together as shown. Figure d 20 mm 25 mm ✓ 200 mm M 150 mm 2 20 mm 1 of 1 Part A If the moment acting on the cross section is M = 460 Nm, determine the resultant force the bending stress produces on the top board. Express your answer to three significant figures and include appropriate units. F = Value Submit μA Provide Feedback 3 Request Answer Units ?
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.