R 0.022 µF 75 2 33 pF Rc. RE 100 k2 Ria 8.2 k2 13 k2 VEE O +5 V Vcc 6 -5 V Figure 14.45 Final design for amplifier with Rin = 75 2 and A, = 50. +,

Q: 47. current. O a. Base. O b. Collector. c. Source. O d. Drain. O e. Emitter. nt is lowest

A: We need to select correct option for bjt  current

Q: a) In the regulator circuit of Figure , Determine Rext if the maximum internal regulator current is…

A: You have posted multiple question, so according to Bartleby guidelines, we are supposed to answer…

Q: The current flowing through the Base is 40 microAmp while the Collector Voltage (Vc) = 6V Determine…

A:

Q: Refer to BJT cascade amplifier in Figure Q2, determine the de bias voltages and collector current…

A:

Q: Figure Q2(c) shows one of the most common BJT amplifier configurations. The output signal from a…

A:

Q: What must be the minimum power rating for the external pass transistor used with a 7815 reguiator in…

A:

Q: The collector characteristics for a certain transistorare shown a. Find the ratio Ic/IB for VCE =10…

A: I hope this helped you and you learned a lot :) If you have any questions or clarification, do not…

Q: The device associated with voltage-controlled capacitance is a a. none of these b. Light-emitting…

A: Given, We have two mcqs. We have to find the answers for the those two. Please see below for the…

Q: Justify, three terminal devices are far more useful than two terminal ones. Describe in detail how…

A: The diode is a two terminal device. A diode has two electrodes and one PN junction The BJT and FET…

Q: basic electronic please give full answer thanks a) Differentiate between JFET and MOSFET…

A:

Q: What are the advantages of active load with respect to passive load in transistors? Write down at…

A: What are the advantages of active load with respect to passive load in transistors?

Q: The maximum permissible junction tem- perature of a certain power transistor is 150°C. It is desired…

A:

Q: c. 3.2 milliAmps

A:

Q: amplifier has a ac voltage gain?

A: The common source voltage amplifier takes AC input at gate and gives AC output the drain terminal.…

Q: Design and calculate the values of collector resistance and base resistance of the common emitter…

A:

Q: R1 R3 Vs Vout R2 Vin Figure 2.2 (c) What is the small-signal output voltage, vout, for the circuit…

A: We need to find out output voltage for given circuit.

Q: Draw the equivalent circuit model and switching characteristics of the device which is having high…

A: A power diode has a P-I-N structure as compared to the signal diode having a P-N structure. Here, I…

Q: XProblem No.2 (P2). A fixed bias NPN BJT (Beta = 80) circuit is connected to a 12VDC supply. The…

A:

Q: 2. A load of 82 is supplied by a single-switch Direct Current (DC) chopper with an input voltage of…

A: Given: A load of 8 Ω is supplied by a single-switch direct current (DC) chopper with an input…

Q: (a) Find and draw the small signal equivalent of this circuit. (b) Find an expression for the…

A: Brief description : For the given MOSFET transistor we need to calculate its voltage gain, output…

Q: Does the common drain voltage follower produce a considerable amplification effect and if so, are…

A: An amplifier is a device that is used to increase a weak signal's strength without changing its…

Q: The waveforms shown in figure (1) the output waveforms of as an astable multivibrator using 555…

A: When Vo = 5 V, capacitor gets charged towards  5V. So capacitor gets charged during the interval…

Q: Q.1/ Figure below shows a CE power amplifier in which the collector resistor serves also as the load…

A:

Q: Please answer the question with steps

A: According to question: 1) The currents 'IB', ICQ and voltage 'VCEQ' are calculated as

Q: Question What must be the minimum power rating for the external pass transistor used with a 7815…

A: Power rating: This is the highest power input. It is the electrical power when the circuit is…

Q: The n-channel enhancement-mode MOSFET of Figure below

A:

Q: Design a circuit to bias the MOSFET in figure shown, so that its drain current is 5  μA. Estimate…

A: MOSFET is the metal oxide semiconductor field effect transistor. It allow the flow of current in a…

Q: A. A voltage regulator circuit provides a constant voltage of (6 V) across a load resistance of (2…

A: Given: Load resistance, RL=2kΩ Minimum current required for Zener operation, Izmin=5mA Maximum…

Q: + Resistor 10k VAC SINE(0 20 10 0 0 0 40) + Diode 1N914 Vdc 5v

A: Given:

Q: Q2(a) A base bias circuit is shown in Figure Q2(a) having B = 200 and VBE=0.3V. Answer the…

A:

Q: Give the information below. Determine: Given the emitter stabilized bias circuit, DC Equivalent…

A:

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.