Q.1/ Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc-Bac-100. a. Determines the de Q-point (Ico and VCEO). b. Determine the voltage gain and the power gain. c. What changes would be necessary to convert the circuit to a pnp transistor with a positive supply? What advantage would this have? +Vce +15 V 100 1O K 0.5 W 22 juF RE 8.2 R 330 1 S00 mV pp 100 uF 36 0

Q.1/ Figure below shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Boc-Bac-100. a. Determines the de Q-point (Ico and VCEO). b. Determine the voltage gain and the power gain. c. What changes would be necessary to convert the circuit to a pnp transistor with a positive supply? What advantage would this have? +Vce +15 V 100 1O K 0.5 W 22 juF RE 8.2 R 330 1 S00 mV pp 100 uF 36 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A. What means by multivibrator. What are the main types of multivibrators. Mention the main techniques used to design these types. Sketch the transistor circuit diagram and its output with comments for each type.
Please answer the question with steps
Given shows the mutual characteristic for a junction gate field effect transistor. When the gate-source voltage is -2.5V, determine the value of drain current, the dynamic value of forward transconductance. -2.5V 2.5V - 12mA 5 mA -5.0-4.5 -4.0 -3.5 -3.0-2.5 -2.0 -1.5 -1.0 -0.5 Gate-source voltage, VGs (V) 0 20 18 16 14 12 10 00 6 4 2 0 Drain current, (mA)
What replaces each of the following elements when we draw the mid-band small-signal equivalent circuit for an amplifier: a. a dc voltage source; b. a coupling capacitor; c. a dc current source?
Fill in the table VB VC VE Ic LE I8 fre IT gm 5V Consider the circuit given at the right. 600k 1.5k =0.7, Vauo, B=165) 100uF Vo 1k 100uF a) Perform DC analysis and calculate all VB =? VC:? branch currents, node voltages, and small signal parameters 3K VE=? Rout b) Draw a small-signal equivalent model n Vin Rin 400K c) Calculate Ri, Rout, and Ay=Vou/Vin -5V
1. For the circuit in Figure 1: a) Calculate the input and output power if the input signal results in a base current of 5 mA ms. b) Calculate the input power đissipated by the circuit if Rs is changed to 1.5 kQ. c) What maximum output power can be delivered by the circuit if RE is changed tol.5 kQ? d) If the circuit is biased at its center voltage and center collector operating point, what is the input power for a maximum output power of 1.5 W? +Vcc (18 V) Re = 16 2 1.2 kS2 B-40 100 pF Figure 1
Pictorially describe the fabrication steps of N-channel E MOSFET. The drawing and steps be in more details
How do you determine when a transistor is in cutoff?
An n-type MOSFET has a turn-on voltage of VTO=0.6V and is operated at a gate-source voltage of 1V. The drain-source voltage is also 1V. In what region is the MOSFET operating? a. Saturation region b. None of the above c. Triode region O d. Ohmic region
The n-channel enhancement-mode MOSFET of Figure below
For the fixed-bias configuration, determine: a. Base Current b. Collector Current c. Collector-Emitter Voltage d. Collector Voltage e. Base Voltage f. Emitter Voltage
Please answer the question with steps