Question B4 Single line diagram of a three bus power system is given in Figure B4.1. Each generator is a) represented by an emf behind the transient reactance. All impedances are expressed in per unit on a common 100 MVA base. Consider all generators are running at their rated voltage and rated frequency with their emf in phase. Determine the fault current, the bus voltages and line currents during the fault when a balanced three phase fault with a fault impedance Zf= 0.16 per unit occurs at bus 2. jo.1 jo.2 jo.1 jo.2 j0.6 2 jo.4 j0.4 3 Figure B4.1

Question B4 Single line diagram of a three bus power system is given in Figure B4.1. Each generator is a) represented by an emf behind the transient reactance. All impedances are expressed in per unit on a common 100 MVA base. Consider all generators are running at their rated voltage and rated frequency with their emf in phase. Determine the fault current, the bus voltages and line currents during the fault when a balanced three phase fault with a fault impedance Zf= 0.16 per unit occurs at bus 2. jo.1 jo.2 jo.1 jo.2 j0.6 2 jo.4 j0.4 3 Figure B4.1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2/The positive-sequence reactances for the power system shown in Figure are in per unit on a common MVA base. Resistances are neglected and the negative-sequence impedances are assumed to be the same as the positive-sequence impedances. A bolted line-to-line fault occurs between phases b and c at bus 2. Before the fault occurrence, all bus voltages are 1.0 per unit. Obtain the positive sequence bus impedance matrix. Find the fault current, the three-phase bus voltages during fault, and the line currents in each phase. T₁ 1 0.15 उह 3 X=j0.05 G₁ j0.6 j0.3 2 T2 j0.05 X=j0.05 G₂
19
Power flow analysis is used for __________________ in power system. a. Stability Analysis b. Future Expansion c. Fault Analysis d. Symmetrical fault analysis
4.In a double line-to-ground fault we can expect thatImmersive reader A) There are currents in the ground connections. B) The current values in the ground connections are zero. C) Short-circuit currents exist in all three phases. D) The currents in the faulted phases are equal. E) N. A.
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
-The symmetrical fault occurs in the terminals of the synchronous generator. Find the direct axis transient reactance of the synchronous generator under the transient period for the data given below, Leakage reactance(Xl)= 1.3 ohm, Armature reactance (Xad)= 1.6 ohm and field reactance (Xf)=5.4 ohm. 2.10 2.53 1.23 4.00 -The existing condition of the power system can be determined by _____________ analysis. Short Circuit Stability Power Flow Transient
For the following single line diagram of a three-phase system, a three-phase fault occurs at point P and just before the fault the line voltage is 18 kV at P. Find out the transient fault current in pu and original value at point P. Take, the given kVA and kV of the G1 as the new base. [hint: the transient and sub-transient reactances of the synchronous generators are assumed to be same. But for the motors, assume that the transient one is 1.7 times of the sub-transient reactance.] 20,000 KV A 6.9KV 15% G1 7000 KVA 5KV Tz 14% 11/33KV 33/6.9 AV 5+j8 s2 (G2 load 20000 KVA 15000 KVA 10% 12%0 25,000 KVA 6.9KV 8% as orebtsansient [Au tue mpedanmees are given per-unit values)
In the shown below power system, both generators G1 and G2 emf’s are equal.All the system data are shown on the system diagram.a) Draw the system diagram in per unit using (MVA)base = 75 and (KV)base =20 KV in the generators side.b) Calculate the three-phase balanced short circuit current (If) at busbar 3 inAmpere and the fault level (MVA)sc in MVA.c) If the fault at busbar 3 is a line-to-line fault, calculate the fault current inAmpere and the fault level (MVA)sc in MVA.
Power system analysis