QUESTION 4 The Thevenin impedance of a source is ZTh=82+ j7102, while the Thevenin voltage is VTh=235+j312 V. Determine the maximum available average power from the source if it is connected to a purely real load. Write your answer in Watts. QUESTION 5 i. P 0.8 pf lagging + P 0.9 pf lagging For the circuit shown above, what is the magnitude of the voltage Vo? Assume that i;= 6 + j0 Arms, P1 = 53 W, and P2 = 54 W. Write your answer in Volts rms.

Q: 5. 6. En S R This can also be tried with 5 NOT gates in series if three is not working. Circuit # 3…

A: The given sequential logic circuit is shown below.We need to fill the truth table for the given…

Q: B) Draw the block diagram and the P&ID for the system in Figure 2 after adding the multiloop cọntrol…

A: A P&ID gives you the information you need to start planning your plant's construction. There are…

Q: What are some applications of E = mc2

A:

Q: Sensors are used to monitor the pressure and the temperature of a c at. The circuitry for each…

A:

Q: For your overhead water tank you have to make a system that detects the water level in the tank…

A: Finite state machines have finite number of states. Based on input and current state machine will…

Q: Which of the following statements about printed circuit boards is correct? O a. It can be single,…

A: PCBs are called as printed circuit boards. They are used as support for electrical and electronic…

Q: 4- In digital computer we considered the controlled buffers can be useful, why?

A: 4- Buffers are a type of register that can be used for storing binary words. The buffers are…

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: Q2. The purpose of ports declaration is * O to connect to internal signals O for connections to…

A: Port are declared to communicate with external devices

Q: Build the full adder circuit and convert it into symbol. Write a detailed explanation about the full…

A: The full adder is a 1-bit adder with the input carry. It has three inputs and two outputs. The block…

Q: *: The main reason to convert from digital to analog or vice versa is The devices works only with…

A: Reason for converting analog to digital and vice versa  1. Information or physical data are…

Q: Enter the correct value (either 1 or 0) in each box; consider each row carefully before deciding on…

A:

Q: Q) A galvanometer is used as a O Current source. O Voltage source. Null detector. Input resistance

A: Galvonometer is a measuring device give deflection when current flows through it.

Q: You are tasked with designing a Vending Machine system that incorporates a Keypad (4x3) for user…

A: According to the question, we need to design a vending machine for the given items as shown below,We…

Q: A set of (4 four) measurements are done for single (object length) measurement ,and recorded as (110…

A: Precision means how close a particular value is to each of the values .

Q: What happens to the system voltage gain if the middle configuration is removed? Are there any…

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: In the figure below Power Processor Stop/Start a. Select one: Input Output O C. O d. Motor O e. b.…

A: The given figure is shown below.

Q: Draw the equivalent circuit for summing amplifier and voltage amplifier.

A: The voltage amplifier is a device that is used to amplify the input voltage signal. An op-amp is…

Q: for what purpose the adders are used in digital systems i.e. full and half adders?

A: Firstly We need to Know What is an ADDER:- In Digital Electronic Adder is a Combinational Circuit…

Q: In series compensation, if the series applied voltage is in quadrature with the liner current: A.…

A: Given voltage across the series compensator is in quadrature with line current (i.e. 90 degrees ),…

Q: 5. What is called Oscillator?

A: An electronic circuit that provides an AC output without any external AC input is called oscillator.…

Q: ff, when the aircraft taking off these two flaps extended "out" the sensor produces a HIGH vol vhen…

A: Please find your answer below in step 2

Q: 2. A. What parameters can be measured with a digital multimeter (DMM)? B. How does the DMM measure…

A:

Q: 1. Build the 1-bit full adder circuit and convert it into symbol (block).  Write a detailed…

A: "Since you have asked multiple questions, I will answer only first question as per Bartleby…

Q: Quèstion 15 Which of the following is not a general safety practice you should follow when using…

A: Question  Which of the following is not a general safety practice you should follow when using…

Q: Q1\ Find the counting state for the counter

A:

Q: D. Q- D, DA Find the state graph for the following parallel counter: clk clk clk (Handwriting…

A: The solution is given below

Q: Answer in 4 sentences only. 4. What happens to current when resistance is increased? 4

A: We need to tell about the effect of resistance on current .

Q: 3. Plot the values from Tables 1 and 2 on a graph with Ip on the y-axis and Vp on the x- axis. 4.…

A: The plots for data in tables 1 and 2 are shown in the figures below.

Q: B)- Observe what happens when the buttons are pushed‍ PB1 M1 O PB2 M2 M2 HH M1 * Fill in the table:…

A: PB1 and PB2: Push buttons.M1: Relay or motor, with normally open contact.M2: Relay or motor, with…

Q: Please help with this with explanation Thanks

A:

Q: The gate of a J-FET must always be ---

A:

Q: Digital Electronics

A:

Q: Q. No. 7: Determine the output of the following instructions and set/reset the values of the status…

A:

Q: Draw a space-division THREE (3)stages switches. There are 9 inputs and 16 outputs. Stage 1 has three…

A:

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.