Q. No. 7: Determine the output of the following instructions and set/reset the values of the status flags. Status flags Sr.No. Instruction MOV AL, 1 Output 1. SUB AL, 2 MOV AL, OFH 2. ADD AL, 1 MOV AL, 10001100b ADD AL, 00000010b MOV AX, 0OFFH 3. 4. ADD AX, 1 MOV EAX, 6 SUB EAX, 7 MOV AL, -128 SUB AL, 1 5. 6.

Q. No. 7: Determine the output of the following instructions and set/reset the values of the status flags. Status flags Sr.No. Instruction MOV AL, 1 Output 1. SUB AL, 2 MOV AL, OFH 2. ADD AL, 1 MOV AL, 10001100b ADD AL, 00000010b MOV AX, 0OFFH 3. 4. ADD AX, 1 MOV EAX, 6 SUB EAX, 7 MOV AL, -128 SUB AL, 1 5. 6.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
please answer ASAP Subject: MICROPROCESSOR
1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code of the program. 3-Perform the program using STEP function. 4-Execute the program and write the results. Object code Mnemonics MOV AX A1 B0 MOV AL B3 MOV BL 04 ADD AL F4 HLT
3.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Solve the following question correctly please.
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
We want to setup a delay time of about 2ms, we have the instruction cycle time equals to 5 microseconds, the following assembly code is written for this aim. The value of X is still missing. The value of X should be: Delay5 movlw D'X movwf conterdelay Delay nop decfsz conterdelay, 1 Delay goto return O a. D 200 O b. D 100 Oc None of these O d. D150
Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)
microprocessors
Draw a state diagram for: Mealy state machine to detect the 1010 sequence. The output becomes one when you receive the sequence of 1100 and the output is zero otherwise. Overlap is allowed between the detected sequences.
Answer all 4 please. For your information last question is true or false