Question 3 The roof system consists of 130 mm thick reinforced concrete slab ( density = 23.6 kN/m²) resting on steel beams (A=15000 mm²) which are supported by steel girders (A= 40000 mm²). Density of steel is 77.3 kN/m³. Determine the magnitude of the axial force acting on column A. Answer in KN rounded-off to 2 decimal places. a a = 7.5 meters b = 3.1 meters B F 3 at beach C G Steel column 130 mm concrete slab

Question 3 The roof system consists of 130 mm thick reinforced concrete slab ( density = 23.6 kN/m²) resting on steel beams (A=15000 mm²) which are supported by steel girders (A= 40000 mm²). Density of steel is 77.3 kN/m³. Determine the magnitude of the axial force acting on column A. Answer in KN rounded-off to 2 decimal places. a a = 7.5 meters b = 3.1 meters B F 3 at beach C G Steel column 130 mm concrete slab

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
Given a simply supported reinforced concrete slab with the effective span lo=2.8 m. The slab is 90 mm thick and reinforced by $10@200 longitudinal bars. The material properties are f= 11.9 N/mm², f= 1.6 N/mm². fy=280 N/mm, and E, = 2.0 x 10 N/mm². Calculate the maximum load (per square meter) that the slab can sustain.
3.1 Show your complete solution.
E2
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and t = | T 12 MPa. w (kN/m) 75 mm 10 mm 0.5 m : 10 mm 3m 10 mm- 150 mm 150 mm
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
1. The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest angle 0 for which the assembly will remain at rest. 20 in. 6 lb 8 lb 20 in.
8.5m Steel girder (A = 21,100 mm?) B -Steel column Problem 1. The floor system of an apartment building consists of a 100-mm-thick reinforced concrete 100 mm concrete slab D. 2 at 3.6 m=7.2 m Steel floor beam (A = 11,800 mm2 slab resting on three steel floor beams, which in turn are supported by two steel girders, as shown in the Figure. The areas of cross section of the floor beams and the girders are 11,800 mm2 and 21,100 mm2, respectively. Determine the dead loads acting on the beam CD and the girder AE.