Question 2 [29] Evaluate the stiffness matrix for the element shown in Figure 2. Assume plane stress conditions. The coordinates are given in units of millimeters. (0, 10) M-3 j=2 E=21x10¹¹ µ=0.25 (0-10) 1-10 mm (20,0) Figure 2

Question 2 [29] Evaluate the stiffness matrix for the element shown in Figure 2. Assume plane stress conditions. The coordinates are given in units of millimeters. (0, 10) M-3 j=2 E=21x10¹¹ µ=0.25 (0-10) 1-10 mm (20,0) Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1700 mm, and the height of the plate is h = 2100 mm. The shear strain at A is known to be +3922 urad. Assume a = 2.7 mm. Calculate the magnitude of dimension b in the figure. a Answer: b= i W B mm x
The state of plane stress at a point is represented by the stress element shown in figure 2. Apply the concept of analytical method to find stresses acting on an element oriented at 30° counter clockwise with respect to the original element.
A state of stress is specified in the figure shown below. Determine the Normal stress oy (mPa) on the Principal Plane if P1 = -9mPa; P2 = 47mPa and v= 25mPa P1 P2
The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 80 MPa and S, = 225 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 55°. S. Answer: Sn = MPa Snt= MPa
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 17 MPa in size. (a) Determine the stresses 0, 0, and the magnitude of Txy and show them on a stress element. (b) Determine the stresses On. Ot, and the magnitude of Tnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between thex and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise). y X Answer: (a) ox= Oy= Txy= (b) on= Ot= Tnt= n (2 MPa MPa MPa MPa MPa MPa
QUESTION 1) In the figure, the rigid ABC rod is held horizontally by E two elastic rods made of steel and bronze materials at points A and B. The cross-sectional area of the steel bar is A,=10 cm and the cross-sectional area of the bronze bar is A,=50 cm. There is no stress in the bars initially. 5m Calculate the forces that will occur in the elastic rods when the temperature decrease by 50°C. steel В A Note: - For steel, modulus of elasticity is E=210 GPa and coefficient of thermal expansion is a,=12x10“ 1/°C 4m bronze rigid - For bronze, modulus of elasticity is E,=90 GPa and coefficient of thermal expansion is a,=19x10“ 1/C D 5m 3m
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are 5x = 19.6 ksi, 5y = 4.3 ksi, and Sxy= 7.3 ksi. Assume ß = 38°. Determine the normal stresses ox and 6, and the shear stress Txy at the point. Say Sx Txy Answers: 0x = oy = Txy || ox ksi. ksi. ksi.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 14 MPa in size. (a) Determine the stresses Ox, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the stresses On, ot, and the magnitude of Tnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise). σ n Answer: (a) ox= Oy= Txy= (b) on= Ot= Int= MPa MPa MPa MPa MPa MPa X
A beam with the cross section shown in the figure carries a bending moment that causes the elastic region to extend 40 mm from the neutral axis. De- termine the residual stress distribution after the bending moment has been removed. Use oy = 280 M Pa. 75 mm 25 mm 75 mm 25 mm 50 mm
80 MPa, Gy 35 MPa, At a point in a machine component that is subjected to plane stress, the normal and shear stresses are ox = and Txy = 42 MPa, acting in the directions shown in the figure. 기 Ox At this point, determine the strain components Ex, y, z, and Yxy. Assume that E = 71 GPa and v= 0.33 for the machine component. Ex = με με με μrad aut || Ez Yxy || || Txy =
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1250 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3780 μrad. Assume a = 2.1 mm. Calculate the magnitude of dimension b in the figure. h a Answer: b = i A W B mm X