Question 13 Help The capacitive level transducer is to be used to measure the depth h of liquid in a tankbetween 0 and 8 m. The total length I of the transducer is 9m and the ratio bla of thediameters of the concentric cylinders is 3.0. The dielectric constant ɛ ofthe liquid is 2.4 and the permittivity of free space ɛo is 8.85pFm. Thetransducer is incorporated into the deflection bridgeR, =1002, R, =10k N and voltage source V, =15 volt , the capacitanceCh when the tank is empty iswithR2ETCo13) (e) For the same question in(11), Using the calculated Co , the level h ifEth =0.19 volts is read from the bridge is

The given bridge is a Wheatstone bridge.

Answered: Question 13 Help

Engineering

Electrical Engineering

Question 13 Help

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
all elements in a circuit that carry the same current are said to be ______ a. closed-loop b. network c. series d. bilateral
1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above.
20.a. What's the primary disadvantage of using copper conductors?A. DurabilityB. CostC. AvailabilityD. Weight20.b. The NEC requires that each service-disconnecting means be suitable forA. hazardous locations.B. disconnecting the meter.C. wet conditions.D. the prevailing conditions 20.c. As a general rule, each building or structure is limited to a single service. What's an automatic exceptionto this rule?A. A second service deemed suitable for useB. A second service having the proper markingsC. Emergency systems or fire pumpsD. Higher building occupancy
Question 3 (a) Discuss and critique the law of electricity supply? (b). Explain with a diagram a Retail competition model of electricity market. (c). Explain effects when government has a bigger say in the operation of Public utilities.
12.a. You're working on an installation at a patient care facility. You have two panelboards next to eachother that supply the critical and the normal feeder circuits. These two panelboards must be bondedtogether using an insulated copper conductor with a minimum size ofA. AWG 10.B. AWG 6.C. AWG 8.D. AWG 4. 12.b. You're installing an isolated power system in a hospital that'll serve a group of patient care areas. Whichof the following colors must be used for the wire that connects to the terminal at each receptacle that'susually reserved for the neutral conductor?A. Green with a white stripeB. Orange with a distinct stripeC. Red with a black stripe
1. The terms “open-circuit", “short circuit" and “dead short" are used in speaking electricity. Answer the following questions about these three terms: a. What is the value of the resistance of an open circuit? b. What is the value of the resistance of a short circuit? c. What is meant by a “dead short"? 5 DDPasalo-Electrical Engineering Department COE MMSU EE 121: Electrical Circuits I 2. When a switch is open, is the resistance between its terminals high or low? ¸Low 3. What is the resistance of a closed switch (ideally)? 4. Using each of the methods shown in (a) and (b) below, calculate the value of the equivalent resistance of a combination of R1 = 5 ohms and R2 = 20 ohms connected in parallel a. Using the equation: 1/Requivalent = 1/R, + 1/R2 + 1/R3 = b. Using the equation: Requivalent = (R, x R2) / (R, + R2) = Ω
Topic: Series Resistor and Voltage Division Consider the following two diagrams of series circuits. For each diagram, use arrows to indicate the direction of the conventional current. Then, make comparisons of the voltage and the current at the designated points for each diagram.
Please solve in 15 min
5. What is the minimum size of rigid metal conduit? a. 3/8 inch trade size b. b. ¾ inch trade size c. c. ¼ inch trade size d. d. ½ inch trade size
13.) Two household electric ranges rated at 13kW shall be calculated at this VA in the load calculations. A. 5.5 B. 8.0 C. 14 D. Either A or B
The hole on the drawing below is required to be perpendicular to the bottom surface and centrally located on the plate regardless of the size of the feature and regardless of the sizes of the datum features. In order of precedence, which datum features are missing in the feature control frame? (select all correct answers) Ø2.505 -2.510 0.005 E C A B Odatums A, D, E Odatums A, D Odatum A O datums D, E, A O datums A, E, D 1 I 6.00 4.00 1.00